F355 Recall # 48- Fuel Divider Block (Warning)

That's why I am having the recall done at my local independent.

 

Ha...Another fail of a fail.

Thank you for sharing and the heads up.

+1.

 

I think the recall has to be done at the dealer.

 

The kit is available for purchase from Ricambi and can be installed by anyone competent.

It won't be free but unless you are near a dealer it will probably cost less at a local shop.
Image Unavailable, Please Login

 

wow that's interesting...I haven't had mine done yet because I can see there's no rubbing on the hose clamp (purposely rotated it out of the way during the engine out major).

Is it an easy fix to avoid this new rubbing on the hood strut? Or does the new delivery block change position enough so that's a new problem?

 

I spotted this on a friend of mines car in the UK the pipes are easily moved out of the way to avoid chaffing, admittedly you should not have to but please check and move them yourself.

 

Competizione told me they won't do it. Only FoW can do the recall.

 

At no cost to the owner.

 

Thanks for the warning, I will check mine in the morning.
I wanted my local independent to do mine but was told that the recall "had to" be done by the Ferrari Dealership due to legal requirements.

 

When I first got my 355, the lines were in slight interference with the driver side lid strut. They caused a small wear mark on it. So I got a couple zip ties and pulled them away just enough so they will not rub anything. No problems with rubbing since.

Though I will take my car in for the recall anyway, just so everything is straight on the records.

 

Took it back to dealer due to very minor chafing on the driver's side engine lid strut...much less than pictured by the OP. Corrected in a few minutes....on my way.

 

They will do it, just not free like the dealer. Comp can't honor a dealer recall for free... Almost be worth it to pay Richard and Fernando to do it then let some dealers do it for free... You know you are getting a 1st class job with Comp cars..

 

I got my fuel block 'recall' job done a few weeks ago and they did a great job!! Fuel lines are not even close to rubbing the struts now .

They also installed a very fancy 'heatsheild' over my carbon canister in the R/side rear bumper . They said it was another factory 355 'campaign' that needed to be done.

 

I am glad I no longer have to worry about you burning up!

 

..........

 

I had both of these campaigns done on my car at FofSF last december with no problems to report.

 

Goth,
When you have a moment, could you please post a picture of that?

Thanks very much,
Dave

 

This is what my car looks like after the recall work done by a dealer. You can see the cloth rub strip that has been bonded to the strut as well as one fuel line that may contact the strut is now encased in a plastic wrap.
Image Unavailable, Please Login

 

I can do that in the next couple days. It actually looks kinda cool .

 

I would like to see a pic of that also. I had my fuel lines done a few weeks ago and they didn't say anything about a heat shield. They did do a recall/campain on my OBD plug though that I had never heard of. I guess some cars had problems talking with state emission computers through OBD2 so they did some kind of ground/plug modification.

 

Interesting. On my car, once my concern was expressed, they adjusted the routing of the lines so there is no way they can contact the strut, without resorting to the shielding you have. Either way, it works.

 

Yup, that is an old recall from about 5 years ago now. Basically Ferrari skipped a ground wire on the plug, so a generic OBDII code scanner could not be used, which is against EPA rules/law (forced you to go to the dealer to read a "check engine" light. It also prevented state emission checks, once states started scanning through OBDII ports rather than using a dynometer and exhaust check. Which started around 2004 or there about...shortly after, then the recall came out.

Now you can scan all the federally mandated Pcodes if the CE light comes up with a generic scanner. The SD1 and SD2 is more useful, but you can get the basic info with a generic scanner.