360 Lowered Expectations | FerrariChat
Buy

360 Lowered Expectations

Discussion in '360/430' started by anxpert, Dec 11, 2010.

This site may earn a commission from merchant affiliate links, including eBay, Amazon, Skimlinks, and others.

  1. anxpert

    anxpert Formula Junior

    Mar 4, 2008
    970
    Oceanside, CA
    Full Name:
    Enrique Mar
    #1 anxpert, Dec 11, 2010
    Last edited by a moderator: Sep 7, 2017
    After ample consideration, I decided to lower my 360. Of concern was diminished ride / handling quality and fender rubbing. This 360 rides on rears 305 / 25 /19 and 235 / 35 / 19 fronts.

    After attempting to adjust the spring height while the coil overs where installed, it became quite clear that removal was / is the best option.

    Prior to lowering the front tire combination rubbed on occasion while turning and going over a dip or driveways with the wheels turned.

    I invested in a lip roller from the Eastwood Company, interchanging the rubber roller with an insert fabricated from an aluminum bat. HEating up the fender lip while rolling was quite simple and I was able to roll the lip completely against the inner fender well and no paint damage.

    Having solved the " lip " problem, I decided to lower the car by 1" in the front and 1" in the rear, equivalent to 12 turns on the spring perches.

    The total job took about 10 hours over two days ..... attached a couple of pictures of the results.

    Overall. the ride quality improved dramatically. I'm sure there are a variety of opinions pro / con on such process .... nevertheless, I don't track the car and living in Southern California the land of endless freeways , handling at high speeds and twisty roads becomes a mute point.

    The car will be aligned next week, as it seems that negative camber was affected by 2 degrees.

    I do think the car looks better, and should it become an issue I can invest another 10 hours in raising the car back to stock.
    Image Unavailable, Please Login
    Image Unavailable, Please Login
     
  2. I'm gone

    I'm gone Formula Junior

    Feb 5, 2006
    619
    Phoenix,az
    Full Name:
    Brian
    #2 I'm gone, Dec 11, 2010
    I like it! these cars look great when lowered, but I would have been scared to heat up the fenders and roll the wheel well! 10 hours of work it quite a job, looks good.
     
  3. asb9987

    asb9987 F1 Rookie

    Dec 4, 2004
    4,191
    Toronto
    Full Name:
    A. B.
    #3 asb9987, Dec 11, 2010
    Good to see another owner willing to get his hands dirty. It looks much better, but the rear looks like it should be slightly lower to match the front, no?
     
  4. alexkam

    alexkam Formula 3

    Mar 14, 2007
    1,116
    Sunny CA
    Full Name:
    Alex
    #4 alexkam, Dec 11, 2010

    +1 on the rear. Looks Great!
     
  5. anxpert

    anxpert Formula Junior

    Mar 4, 2008
    970
    Oceanside, CA
    Full Name:
    Enrique Mar
    #5 anxpert, Dec 11, 2010
    Last edited by a moderator: Sep 7, 2017
    I ws attempting to keep the same ratio of rake and drive it a few days to confirm if all is well. Now that I've dabbled in the process, I might try 1/2 an inch lower in the front and another 1" in the back. The best part of the project, regardless of the lowering has been the rolling of the fender lips. I have now driven over prior known " hit/rub " spots without a single incident. I will post pictures of the finished rolled lip. Attached ..reference of my lowered , that inspired the whole lowering idea.
    Image Unavailable, Please Login
     

Share This Page