CS Harness | FerrariChat
Buy

CS Harness

Discussion in '360/430' started by bayareaferrari, Apr 3, 2011.

This site may earn a commission from merchant affiliate links, including eBay, Amazon, Skimlinks, and others.

Page 1 of 2
  1. bayareaferrari

    bayareaferrari Formula Junior

    Dec 19, 2004
    672
    California
    #1 bayareaferrari, Apr 3, 2011
    Where do you buy the racing harness/belts for the CS? Meaning factory or close to factory Ferrari belts?
     
  2. arizonaitalian

    arizonaitalian Two Time F1 World Champ
    Owner Silver Subscribed

    Oct 29, 2010
    20,507
    Wyoming
    #2 arizonaitalian, Apr 3, 2011
    Dealer should have them. Also check Ricambi. An F-chatter just bought the car from Algar that had a "bar" installed behind the seats and four point belts installed by the dealer....check the CS market thread and you can find him...

    I am not going to get them in my car because (it seems) you have to modify the car and make holes to find a way to anchor them. I would like to have the harness for track days, but don't want to mod/drill holes on the car (at least not right away).
     
  3. stokpro

    stokpro F1 Rookie
    Lifetime Rossa Owner

    Jun 25, 2003
    4,383
    Himalayas
    #3 stokpro, Apr 3, 2011
    Becoming increasingly rare to find. I have a brand new OEM set available. You have a PM.
     
  4. bayareaferrari

    bayareaferrari Formula Junior

    Dec 19, 2004
    672
    California
    #4 bayareaferrari, Apr 3, 2011
    Hold the phone...These cars are build to be on the track and you are telling me that it will screw it up to add the harness system which the seats are built for?

    I would like for the car to have the ability for use of some harness. What does this actually involve?

    Is this a major project?
     
  5. arizonaitalian

    arizonaitalian Two Time F1 World Champ
    Owner Silver Subscribed

    Oct 29, 2010
    20,507
    Wyoming
    #5 arizonaitalian, Apr 3, 2011
    No, not at all.

    I hope you didn't infer that from my post about needing something to anchor the belts too. That is not a "major project" by any stretch. Call a dealer or wait for one of the many folks on here who have put 4 pointers in their track cars to chime in.

    (BTW, the US cars didn't come with the four pointers because - as I understand it - they don't meet regulatory requirements over here and/or would require new testing in order to do so (not sure which or if both)).
     
  6. bayareaferrari

    bayareaferrari Formula Junior

    Dec 19, 2004
    672
    California
    #6 bayareaferrari, Apr 3, 2011
    Thanks for the clarification. I am really looking to see how simple adding the harness system is to the car.

    What parts are needed?
    How difficult?
     
  7. rcallahan

    rcallahan F1 Rookie
    Owner

    Jul 15, 2002
    3,307
    Santa Barbara
    Full Name:
    Bob Callahan
    #7 rcallahan, Apr 4, 2011
    You should have a roll bar if you install these harnesses.
     
  8. spiderscott

    spiderscott Formula 3
    Silver Subscribed

    Feb 24, 2004
    1,661
    Ratarossa HQ UK
    Full Name:
    Ratarossa
    #8 spiderscott, Apr 4, 2011
    im in the process of installing a set of ferrari harnesses. I will do a write up when I start the project.
     
  9. spiderscott

    spiderscott Formula 3
    Silver Subscribed

    Feb 24, 2004
    1,661
    Ratarossa HQ UK
    Full Name:
    Ratarossa
    #9 spiderscott, Apr 5, 2011
    Last edited by a moderator: Sep 7, 2017
  10. spiderscott

    spiderscott Formula 3
    Silver Subscribed

    Feb 24, 2004
    1,661
    Ratarossa HQ UK
    Full Name:
    Ratarossa
    #10 spiderscott, Apr 5, 2011
    Last edited by a moderator: Sep 7, 2017
  11. Ingpr

    Ingpr F1 Rookie

    Jun 30, 2009
    2,619
    PR
    Full Name:
    David
    #11 Ingpr, Apr 5, 2011
    Looks fantastic!!!
     
  12. arizonaitalian

    arizonaitalian Two Time F1 World Champ
    Owner Silver Subscribed

    Oct 29, 2010
    20,507
    Wyoming
    #12 arizonaitalian, Apr 5, 2011
    That factory set up looks awesome. I would love to do that to my car.

    Where do they go after they go through the Alcantara and into the engine bay??

    Anyone done this to a 3-point car? (Got pics and details on where, what, how much etc)
     
  13. Juri

    Juri Formula Junior
    BANNED

    Mar 15, 2010
    604
    Houston, TX
    Full Name:
    Juri
    #13 Juri, Apr 5, 2011
    This is a very nice upgrade !
    Where exactly (which company?) one can purchase this harness and the rest of the system that goes into the wall behind the seats?
     
  14. spiderscott

    spiderscott Formula 3
    Silver Subscribed

    Feb 24, 2004
    1,661
    Ratarossa HQ UK
    Full Name:
    Ratarossa
    #14 spiderscott, Apr 5, 2011
    These are ORIGINAL Ferrari items so you can get them from main dealer or I know that Ricambi supply them:

    http://www.ricambiamerica.com/product_info.php?products_id=261371


    they are not cheap @ $459 each, I paid slightly less than this in the U.K

    Mounting points: Here its not so straight forward, Ferrari do not supply the plates they used for the harnesses. You either had them as part of your build spec or not at all.

    However if you search EBAY for 'Harness backing or plate' make sure you get FIA approved ones and you need a 7/16" thread. Everything else is supplied with the Ferrari belts inc a nice set of Ferrari badged belt pads for comfort.

    Mounting wise Im still not 100% sure. i want to followed more or less what the factory did but might drill a hole through the rear wall and mountthese plates on the engine side and bolt through that way?? I need to take a close look, otherwise will see if these are able to be welded (as Ferrari did) on the inside of the car, but two different metals so not sure if this can be done ??
     
  15. Juri

    Juri Formula Junior
    BANNED

    Mar 15, 2010
    604
    Houston, TX
    Full Name:
    Juri
    #15 Juri, Apr 5, 2011
    Thank you for such a valuable information!
     
  16. bayareaferrari

    bayareaferrari Formula Junior

    Dec 19, 2004
    672
    California
    #16 bayareaferrari, Apr 10, 2011
    any update on your project?
     
  17. Ricambi America

    Ricambi America F1 World Champ
    Sponsor Owner

    Dec 7, 2003
    16,451
    Winston Salem, NC
    #17 Ricambi America, Apr 10, 2011
  18. spiderscott

    spiderscott Formula 3
    Silver Subscribed

    Feb 24, 2004
    1,661
    Ratarossa HQ UK
    Full Name:
    Ratarossa
    #18 spiderscott, Apr 10, 2011
    Last edited by a moderator: Sep 7, 2017
    not much of an update my end, ive had a few engine issues ive had to focus on, but all fixed now so will start again to look at the new belt install + other projects

    Im steering toward mounting the brackets in the engine bay as these can be hidden behind 1) two center brackets will be behind the plastic cover
    2) two outer brackets will be behind the Carbon Engine Side Panels

    So neither will be seen and the modification will look factory stock.

    I need to take some measurements to be 100% they will fit where I want them as the fuel line/bar runs along that area so need to check for space/restrictions.

    Some pics of intended positions:
    Image Unavailable, Please Login
     
  19. spiderscott

    spiderscott Formula 3
    Silver Subscribed

    Feb 24, 2004
    1,661
    Ratarossa HQ UK
    Full Name:
    Ratarossa
    #19 spiderscott, Apr 10, 2011
    Last edited by a moderator: Sep 7, 2017
  20. spiderscott

    spiderscott Formula 3
    Silver Subscribed

    Feb 24, 2004
    1,661
    Ratarossa HQ UK
    Full Name:
    Ratarossa
    #20 spiderscott, Apr 10, 2011
    Last edited by a moderator: Sep 7, 2017
  21. sheld

    sheld Rookie

    Jul 31, 2008
    1
    #21 sheld, Apr 11, 2011
    Hi Scott,
    really looking forward to how you do this, as i have some on order. What are you going to do with the inner trims?.
    Regards Sheldon
     
  22. stokpro

    stokpro F1 Rookie
    Lifetime Rossa Owner

    Jun 25, 2003
    4,383
    Himalayas
    #22 stokpro, Apr 12, 2011
    Last edited by a moderator: Sep 7, 2017
  23. spiderscott

    spiderscott Formula 3
    Silver Subscribed

    Feb 24, 2004
    1,661
    Ratarossa HQ UK
    Full Name:
    Ratarossa
    #23 spiderscott, Apr 26, 2011
    Last edited by a moderator: Sep 7, 2017
    Im getting a little futher with my harness install, sorry its slow progress im trying to do too many jobs at once as usual !

    So today I cut out the holes in the factory CS trim to enable the belts to pass through, one thing I like about the factory supplied belts is when purchased they also come with the 4 plastic trim cover lugs already supplied so all you have to do is cut the holes and the black plastic covers finish off the look and keep it all tidy.

    a few pics ...
    Image Unavailable, Please Login
    Image Unavailable, Please Login
    Image Unavailable, Please Login
    Image Unavailable, Please Login
     
  24. F430addict

    F430addict F1 Rookie

    Sep 17, 2010
    4,460
    #24 F430addict, Apr 26, 2011
    Sweet! Subscribed!
     
  25. Ingpr

    Ingpr F1 Rookie

    Jun 30, 2009
    2,619
    PR
    Full Name:
    David
    #25 Ingpr, Apr 28, 2011
    Hi Scott!
    Can you update on this?
     
Page 1 of 2

Share This Page