328 Front wheel bearing nut torque | FerrariChat
Buy

328 Front wheel bearing nut torque

Discussion in '308/328' started by Iain, Apr 23, 2012.

This site may earn a commission from merchant affiliate links, including eBay, Amazon, Skimlinks, and others.

Page 1 of 2
  1. Iain

    Iain F1 Rookie

    Jan 21, 2005
    3,320
    UK
    #1 Iain, Apr 23, 2012
    Can anyone confirm how tight this should be done up? Its not in the 308/328 WSM but the Mondial 8 manual says (on page M8) 45 KgM (325 lbFt). Does anyone know if that's right or is it another Ferrari special WSM typo?
     
  2. Iain

    Iain F1 Rookie

    Jan 21, 2005
    3,320
    UK
    #2 Iain, Apr 23, 2012
  3. Matto

    Matto Formula 3

    Dec 26, 2011
    2,085
    Mooresville, NC USA
    Full Name:
    Matthew
    #3 Matto, Apr 23, 2012
  4. Iain

    Iain F1 Rookie

    Jan 21, 2005
    3,320
    UK
    #4 Iain, Apr 23, 2012
    Thanks but not - the 328 (and Mondials & TR's) use a completely different design of bearing system - not the traditional tapered needle bearings, so (as far as I understand it) its not a matter of setting the bearing up in the usual way. You do the retaining nut up to a specific torque.

    See http://www.eurospares.co.uk/userImages/059/Large/059_043.gif

    What I'd like to know is what the nut labelled "5" should be done up to.
     
  5. fastradio

    fastradio F1 Rookie
    BANNED Professional Ferrari Technician

    Apr 26, 2006
    3,664
    New England
    Full Name:
    David Feinberg
    #5 fastradio, Apr 23, 2012
    From the 328 Technical Summary
    22 kg-m 158.5lb-ft (Fastener size 27x1.5mm)
     
  6. Iain

    Iain F1 Rookie

    Jan 21, 2005
    3,320
    UK
    #6 Iain, Apr 23, 2012
    Many thanks David.
     
  7. Matto

    Matto Formula 3

    Dec 26, 2011
    2,085
    Mooresville, NC USA
    Full Name:
    Matthew
    #7 Matto, Apr 23, 2012
    Youtheman, David.
     
  8. Iain

    Iain F1 Rookie

    Jan 21, 2005
    3,320
    UK
    #8 Iain, Apr 23, 2012
    Found this in the tech spec (didn't think to look in there !) but I'm wondering if this is not in fact the ring nut that holds in the rear hub? ."Securing Axle Shaft flange to wheel shaft" sounds like something to do with a driven wheel

    Part 8 in this diag.

    http://www.ricambiamerica.com/parts_catalogs.php?M=FE&P=&V=diag&I=2495

    The thing listed above it in the tech spec "Securing Steering knuckle lever" is interesting purely because of the size of the nut (20 x 1.25). WIll have to take a wheel off & measure,, but if its the right size, maybe that's it (16Kgm/115 lbft)
     
  9. Steve Magnusson

    Steve Magnusson Two Time F1 World Champ
    Lifetime Rossa

    Jan 11, 2001
    26,790
    30°30'40" N 97°35'41" W (Texas)
    Full Name:
    Steve Magnusson
    #9 Steve Magnusson, Apr 23, 2012
    TR happen to use the same bearing (112799) and nut (124642) on the front "wheel shaft" as the 328 (and, on the later version of each, the exact same wheel shaft is also used -- although installed in different directions). The TR spec is (clearly) given as 25 kg-m in the TR WSM so 22~25 kg-m must be in the right ballpark -- but please do confirm/deny the thread size, if possible. The early 328 wheel shaft looks a little more iffy construction-wise so I might go with the 22 kg-m on that, but, if you have the later 328, I'd use 25 kg-m without worry -- JMO.
     
  10. Iain

    Iain F1 Rookie

    Jan 21, 2005
    3,320
    UK
    #10 Iain, Apr 24, 2012
    Thanks Steve. When I get some time I'll take a wheel off & have a look.
     
  11. andyww

    andyww F1 Rookie

    Feb 7, 2011
    2,775
    London
    #11 andyww, Apr 24, 2012
    The 348 WSM also confirms 25 Kg-m and that is identical in every way including the ABS wheel on the other end.

    I wonder what that 20mm figure in the 328 list is supposed to be for? Fact is, that list seems woefully inadequate and vague.
     
  12. Iain

    Iain F1 Rookie

    Jan 21, 2005
    3,320
    UK
    #12 Iain, Apr 24, 2012
    That would seem to settle it then.

    ..and now I need a new torque wrench (which will probably not get used for anything else) because mine doesn't go that high! :(

    (Either that or I have to find an extension for it.....)
     
  13. Constance

    Constance Karting

    Apr 10, 2009
    213
    Kembs - France
    Full Name:
    Constance
    #13 Constance, Apr 24, 2012
    Last edited by a moderator: Sep 7, 2017
    This is my own experience about front bearing replacement on my 328

    regarding the best price, the Citroën SNR R166.08 95619166 for CX serie 2 between 1985 and 1991.

    ---> Size: 50x116x36,4 / 6Ø, 8x1,25 (mm)

    http://www.oscaro.com/roulement-de-roue-snr-r166-08-1294354-654-p



    The torque value for the 6 bolts 8mm * 1.25 on the outer daceto the hub carrier is 2.1 Kg/m

    The torque value for the main nut 20mm * 1.25 16 Kg/m

    (Values to be confirmed)
    Image Unavailable, Please Login
    Image Unavailable, Please Login
    Image Unavailable, Please Login
    Image Unavailable, Please Login
    Image Unavailable, Please Login
    Image Unavailable, Please Login
    Image Unavailable, Please Login
    Image Unavailable, Please Login
    Image Unavailable, Please Login
    Image Unavailable, Please Login
    Image Unavailable, Please Login
    Image Unavailable, Please Login
    Image Unavailable, Please Login
    Image Unavailable, Please Login
    Image Unavailable, Please Login
    Image Unavailable, Please Login
    Image Unavailable, Please Login
    Image Unavailable, Please Login
    Image Unavailable, Please Login
     
  14. Iain

    Iain F1 Rookie

    Jan 21, 2005
    3,320
    UK
    #14 Iain, Apr 25, 2012
  15. Constance

    Constance Karting

    Apr 10, 2009
    213
    Kembs - France
    Full Name:
    Constance
    #15 Constance, Apr 25, 2012
    Last edited by a moderator: Sep 7, 2017
  16. Iain

    Iain F1 Rookie

    Jan 21, 2005
    3,320
    UK
    #16 Iain, Apr 25, 2012
    Thanks Constance - are there any markings on it to indicate what grade it is?
     
  17. Constance

    Constance Karting

    Apr 10, 2009
    213
    Kembs - France
    Full Name:
    Constance
    #17 Constance, Apr 25, 2012
    Last edited by a moderator: Sep 7, 2017
  18. andyww

    andyww F1 Rookie

    Feb 7, 2011
    2,775
    London
    #18 andyww, Apr 25, 2012
    Constance, I am interested to know where you got the figure of 16 KG-M from. This corresponds exactly to the figure mentioned in the 328 tech specs for an unidentified 20mm nut (see above post) and also happens to be the figure I used. Did you get this figure from a different source of information?

    When I replaced mine I ordered an SNR bearing from a bearing supplier but the oil seal fitted on it was too big and rubbed against the stone shield, a problem someone in the Testarossa forum also had. I had to do a modification to make it fit.
    http://www.ferrarichat.com/forum/showthread.php?t=348614
     
  19. David Lind

    David Lind Formula 3

    Nov 19, 2008
    2,248
    Full Name:
    David Lind
    #19 David Lind, Apr 25, 2012
    If you're worried about your nuts being too highly torqued, for heavens sake don't watch the news!
     
  20. andyww

    andyww F1 Rookie

    Feb 7, 2011
    2,775
    London
    #20 andyww, Apr 26, 2012
    Last edited by a moderator: Sep 7, 2017
    Looking again at the excellent pictures above, I can now see why you didnt have the problem I had with the large rubber oil seal on the SNR bearing rubbing on the stone shield. The shield is missing! That does avoid the problem I suppose!
    One of the pictures shows the seal more clearly than mine did
    Image Unavailable, Please Login
     
  21. Iain

    Iain F1 Rookie

    Jan 21, 2005
    3,320
    UK
    #21 Iain, Apr 26, 2012
    Good spot - so does that seal remove the need for the stone/dust shield? If that's pressed down right against the back side of the hub then it may even be a better system?
     
  22. andyww

    andyww F1 Rookie

    Feb 7, 2011
    2,775
    London
    #22 andyww, Apr 26, 2012
    If the vertical lip on the new seal were acting on the hub I think it would just wear out very quickly. But it doesnt. This lip does seem designed to have the same function as the stone shield though, but I cant see it being better. The original shield is metal and encases the entire bearing.
    The SNR part number stamped on the bearing I used is the same number as visible on the picture on Superformance website, so presumably this issue also affects bearings supplied by them. Their picture shows the other side though so cant see what type of seal it has.
     
  23. Constance

    Constance Karting

    Apr 10, 2009
    213
    Kembs - France
    Full Name:
    Constance
    #23 Constance, Apr 26, 2012
    Last edited by a moderator: Sep 7, 2017
    The weather shield will prevent water projections to bearing inner flange, and the grease to contaminate the brake disc (seeping). The flange is not sealed.
    The lipseal and the seal runner should be lubricated before assembling

    Regarding the torque value, if I remember, I got the torque value from Modena Motors (France)


    Sorry for the tipo errors
    Image Unavailable, Please Login
    Image Unavailable, Please Login
    Image Unavailable, Please Login
    Image Unavailable, Please Login
    Image Unavailable, Please Login
    Image Unavailable, Please Login
    Image Unavailable, Please Login
     
  24. Iain

    Iain F1 Rookie

    Jan 21, 2005
    3,320
    UK
    #24 Iain, Apr 26, 2012
  25. Constance

    Constance Karting

    Apr 10, 2009
    213
    Kembs - France
    Full Name:
    Constance
    #25 Constance, Apr 26, 2012
Page 1 of 2

Share This Page