Scuderia Decal Stripe - has anyone installed on a scud that did not come with one

It's all up to you. Yes. The clear bra needs to be removed in order to do a proper job but who's to say you can't have the stripe put on the clear bra? I've seen some companies print the scud stripe on a thin film (almost close to skin thin), layer it on then clear coat the entire bonnet. The result was an almost paint like stripe as opposed to thick decals that pop.

 

Most of our Stripes finish up on the original models.
The quality of ours is such, that you can't distinguish it from a factory original until you run your fingers over it.
However, if you are fitting a Stripe and a clear bra, here is some advice.
First, let me explain what happens if you apply a clear bra over the top of the Stripe.
Even though the Stripe is only a few microns thick, when you put the clear bra over the top, the clear won't adhere perfectly over the edge of the Stripe and because it's clear you will see the ridge and the very small air gap through the clear material, this will be quite noticeable.
However, when you put the Stripe on top of the clear bra, even if you only do half the hood, there is only a small transition point where the Stripe goes from the bra to the paint and because the Stripe is not transparent its very hard to see. If you do all of the hood in clear you wont see it at all, which is what we recommend.
If you are going to drive the car, the bra and the Stripe will get damaged in time. There is also a high gloss clear coat on the Stripe, it's thinner but fairly tough like the bra, but it's not bullet proof.
You'll probably find, that if the Stripe is put on professionally, you won't be able to get it off without damaging the bra.
At some point you may have to replace both, that's why we supply the spare.
To sum up, put the bra on first then put on the Stripe.
Ciao
Brenden

 

Brenden you make the 16M stripe decal? Can u PM me price (for 430)

 

I think it is $395 but Brendan will confirm.

 

Hi Edward,
I've sent you a PM, all the details are on our website.
Even though the factory 16M Stripe was for a Spider, our kit is for a Coupe and comes with a spare front segment like the others.
As a matter of fact, if you are putting it on a Spider, you've got enough left over to do another Spider.
Ciao
Brenden

 

Thanks Paul, you're quite right.
I'm asleep, while you guys are busy on FerrariChat.

 

Not much good showing you photos on a 430, but here are some on 360s.
The photos of the Rosso 360 are from a Japanese customer, he finished the back like a CS Stripe, probably because the wing would have obscured the way a Scuderia Stripe is normally finished, on top of the engine lid.
The way the color of the Scuderia Stripe appears is very subjective to the color of the car and the lighting, in all these pictures it's the exact same Scuderia Stripe.
The most striking, is the difference between the Grigio Nurburgring and the Grigio Silverstone.
Ciao
Brenden
Image Unavailable, Please Login
Image Unavailable, Please Login
Image Unavailable, Please Login
Image Unavailable, Please Login
Image Unavailable, Please Login
Image Unavailable, Please Login

 

I like the rear deck on the 360.

 

Does anyone know if 360performance stripe has the black and silver on the same plain. So if you ran your finger across it there would not be any thickness difference.

 

Hi Robert,
Ours is digitally printed like the factory Stripe, not layered. However, even though our Scuderia Stripe is a mylar only a couple of microns thick, you can feel the outside edge. Although, with the high gloss clear finish, it's impossible to pick it from the factory Stripe until you run your fingers over the edge. Most of our Stripes finish up on the cars that left the factory without the Stripe option.
Ciao
Brenden

 

Brenden, thanks for a great answer. You anticipated and answered up all of my questions in one posting. I like the idea and product. Inexpensive way to get a "whole new look" on my F430.

 

Why not buy one with stripe? Resale will likely be much better

 

You're welcome.

 

Too late. It was a great deal. One of those you could not walk away from. So I did not and bought it

 

Pix please....I wanna see one without stripes..again

 

I just ordered the stripe online and also sent you a PM. Can you please confirm that you received my order. Thanks. Also Anything you can do to get the stripe to me faster would be greatly appreciated.

 

Hi Robert,
Confirmed, all of the above.
Since it's Monday AM here, it's going out the door as we speak.
I'll email you details about the delivery process.
You'll have to post some good pictures when it's all done.
Ciao
Brenden

 

Will do

 

FINALLY got a chance to sit down and respond and let everyone know that the stripe is PERFECT and I would highly recommend it and 360Performance !!! !!!

 

although more expensive than some of the other stripe options out there, I do like the idea of how thin this product is compared with the layering technique used by others.

 

Here's stripes on my 360






Sent via itty bitty electrons

 

Great product
Image Unavailable, Please Login

 

Hi Robert,
I don't know if I ever thanked you for that wonderful recommendation, with this "Many Thanks".
Ten years on and we're still going strong and I believe we still have the best product on the market.
We have added to our product range since then and we are able to supply the other Stripes as well.
As you can see, they look great on any model, including my 308GT4 historic race car, although most of our Stripes finish up on the correct models that left the factory without one.
Ciao
Brenden
Image Unavailable, Please Login
Image Unavailable, Please Login
Image Unavailable, Please Login
Image Unavailable, Please Login