Anyone tried this "upgraded" window lift motor? | FerrariChat

Anyone tried this "upgraded" window lift motor?

Discussion in '308/328' started by greg288, Oct 23, 2016.

This site may earn a commission from merchant affiliate links, including eBay, Amazon, Skimlinks, and others.

  1. greg288

    greg288 Karting

    May 28, 2007
    203
    Has anyone tried this window regulator/motor set-up?

    Ferrari 308 Door Window Lift Motor # 60030509 | eBay

    It certainly looks more beefy and industrial than the usual part however it is twice the going rate for the normal replacement and doesn't feature the manual crank hole.
     
  2. waymar

    waymar Formula 3

    Sep 2, 2008
    1,354
    Northeast, PA - USA
    Full Name:
    Wayne Martin
    The stock mechanism is easily cleaned and rebuilt. The motor is usually ok. My windows would not move without hand assistance. After reworking the mechanism the windows move with ease. I also replaced the window channel molding.
     
  3. George Vosburgh

    George Vosburgh F1 Rookie
    Silver Subscribed

    I have seen this motor and considered trying them. "Birdman" recommends a unit that sends the correct amperage to the motor which he says the original design layout does not do. Which is why everyone has problems with the windows. I'm going to address this problem this off season. Film at eleven.....
     
  4. dflett

    dflett Formula 3
    Silver Subscribed

    Jun 24, 2005
    1,632
    NY
    Full Name:
    David
    Mine were slow and the passengers even stopped half way down. Cleaned both gearboxes and realigned/retensioned passenger side and both sides are ok now with stock motors and wiring. Sometimes they just need cleaning/servicing
     
  5. 308inSD

    308inSD F1 Veteran
    Owner Silver Subscribed

    Aug 17, 2010
    8,979
    SD, CA
    Full Name:
    Greg
    The hard part of the job is rewinding and rerouting the wire, right? How challenging was that?
     
  6. dflett

    dflett Formula 3
    Silver Subscribed

    Jun 24, 2005
    1,632
    NY
    Full Name:
    David
    #6 dflett, Oct 25, 2016
    Last edited: Oct 25, 2016

    Not very difficult. You can use cable ties to hold the winding while your route the cables. But do draw a picture of how the cable is routed before you take it off and make the replacement cable the same length as the one you take off.
     
  7. Martin308GTB

    Martin308GTB F1 Rookie

    Jan 22, 2003
    4,259
    Black Forest Germany
    Full Name:
    Martin N.
    #7 Martin308GTB, Oct 25, 2016
    Last edited by a moderator: Sep 7, 2017
    There even exists a helping tool. I got mine together with a used motor assembly from TRutlands many years ago.
    Worth its weight in gold.

    Best Regards
    Martin
    Image Unavailable, Please Login
     
  8. robo330

    robo330 Formula Junior

    Apr 15, 2014
    608
    Michigan USA
    Full Name:
    Karl Robertson
    The glass on my car was very slow, in fact sometimes would not lift at all. I lubricated the motors and drive shafts without removing them. Installed Birdman Fuse Blocks and the suggested Window Accelerators (see the Birdman website) and the windows go up and down really fast for an old car. The Window Accelerators made a huge difference, but Jonathan Birdman's Fuse Blocks increased the Voltage to the electric motors significantly. I would suggest lubricating the cables and pulleys when you have the Door Trim off. I believe this was all covered in another Thread on this site. Do take a look!
     
  9. robo330

    robo330 Formula Junior

    Apr 15, 2014
    608
    Michigan USA
    Full Name:
    Karl Robertson
    The Window Accelerators are available from Rodney Dickman - refer: Birdman's 308 site.
     
  10. ATSAaron

    ATSAaron Formula 3
    Silver Subscribed

    Jun 1, 2004
    1,135
    Shady Shores, TX
    Full Name:
    Aaron Bunch
    These new style motors are amazing. I got mine from TRutlands.

    Aaron
     
  11. robo330

    robo330 Formula Junior

    Apr 15, 2014
    608
    Michigan USA
    Full Name:
    Karl Robertson
    Is that $499 for 1 or 2 motors? Seems a lot to me,,,?
     
  12. ATSAaron

    ATSAaron Formula 3
    Silver Subscribed

    Jun 1, 2004
    1,135
    Shady Shores, TX
    Full Name:
    Aaron Bunch
    TRutlands was about $600 for two I think.
     
  13. robo330

    robo330 Formula Junior

    Apr 15, 2014
    608
    Michigan USA
    Full Name:
    Karl Robertson
    The 2 Fuse Blocks from Jonathan Birdman cost $180 plus the Window Accelerators from Larry Dickman cost $119. All up $299 plus S&H. Not bad I think!
     
  14. greg288

    greg288 Karting

    May 28, 2007
    203
    #14 greg288, Oct 25, 2016
    Last edited: Oct 25, 2016
    Thank you Aaron!

    I was very aware of all the typical problems and suggested fixes for them.
    I was simply asking if anyone had actually tried out these new style motors/regulators.

    And thanks for the shopping tip.....I'll take $600 over $1K for a pair any day.
     
  15. ATSAaron

    ATSAaron Formula 3
    Silver Subscribed

    Jun 1, 2004
    1,135
    Shady Shores, TX
    Full Name:
    Aaron Bunch
    I had a video of mine somewhere. Window down and back up takes about 10 seconds per side now.

    Aaron
     
  16. kafugelum308

    kafugelum308 Formula Junior

    Jun 6, 2003
    610
    Northwest
    Full Name:
    M Bradley
    I have two of them on my 308. I had cleaned the existing ones and was never happy with the results. These were a bit of a pain to run the cable but there was ample direction on FerrariChat. I am very pleased with the result.
     
  17. smg2

    smg2 F1 World Champ
    Sponsor

    Apr 1, 2004
    16,329
    Dumpster Fire #31
    Full Name:
    SMG
    Amperage draw is the problem, use the dual relay circuit posted at least a decade ago. Just need to add a power lead from the fuse box... Instant faster windows for $20 and an afternoon.
     
  18. dinoart

    dinoart Formula Junior
    Silver Subscribed

    Oct 30, 2004
    798
    Westminster CA
    Full Name:
    David
    Martin
    Where can I get this tool? Is it still available? I don't see it under TRutlands. Thanks
    David
     
  19. Martin308GTB

    Martin308GTB F1 Rookie

    Jan 22, 2003
    4,259
    Black Forest Germany
    Full Name:
    Martin N.
    Hi David,

    this tool is not, and never was available separately. It just held the cable on the spool for packaging and transport purposes. But it really helps while working on the windows.
    Therefore I redesigned this tool myself and sell it as a 3d printed part. I don't know, whether it's allowed to link to the sale ads section, where I have a thread. Therefore I will send you it via PM later.

    Best from Germany
    Martin
     
  20. 2NA

    2NA F1 World Champ
    Consultant Owner Professional Ferrari Technician

    Dec 29, 2006
    18,221
    Twin Cities
    Full Name:
    Tim Keseluk
  21. JohnInItaly

    JohnInItaly Karting

    Feb 5, 2019
    118
    California
    Full Name:
    John McCoy
    Birdman fuse blocks and grease on the cables made such a huge difference that I plan no further work on my windows. They work just fine.
     
  22. mike996

    mike996 F1 Veteran

    Jun 14, 2008
    6,871
    Full Name:
    Mike 996
    I'd ask the same question I usually do regarding "upgrades" to existing systems...In this case, "Did the windows go up/down adequately when the car was new?" If not, then yes, something better is needed, if they DID, then unless the motor has failed or parts are broken, cleaning (to include electrical connections) and lubrication will restore it to operating as it did...

    Whether they worked OK when new, I don't know though I rented a couple of several-year old 308's when in Hawaii back in the 80's and I don't recall the windows being unusual in their up/down performance. But admittedly that wouldn't have been something I was particularly concerned about while doing my (poor) Magnum impersonation. ;)
     

Share This Page