Repanting 360 manifolds | FerrariChat
Buy

Repanting 360 manifolds

Discussion in '360/430' started by Slc2nd, Nov 8, 2017.

This site may earn a commission from merchant affiliate links, including eBay, Amazon, Skimlinks, and others.

  1. Slc2nd

    Slc2nd Rookie

    Aug 28, 2017
    6
    Roswell Ga
    Full Name:
    Stanton Clark
    #1 Slc2nd, Nov 8, 2017
    Hello I am new to the forum. I was trying to research any posts or advice on repainting manifolds on a '03 360 spyder. I recently purchased this car from the Jersey coast and it has some significant corrosion / flaking paint on the manifolds (see picture below). I will be due for a major service in the next 12-18 months so planning on having the manifolds pulled and refinished properly at that time. However, in the mean time I wanted to explore repainting them with some VHT wrinkle paint purchased from my local Ferrari dealer. I know it will probably not be "factory correct" but hoping to make it look better short term before the next major service.

    I'm sure there are probably some great posts/discussions in the archives on this topic but being new I don't seem to be able to find anything too specific (still learning but this is a great forum). Thanks in advance for any help/guidance......


    Image Unavailable, Please Login
     
  2. Dave rocks

    Dave rocks F1 World Champ
    BANNED

    Nov 23, 2012
    16,047
    Orchard Park, NY
    Full Name:
    Dave Lelonek
    #2 Dave rocks, Nov 8, 2017
  3. Mickster

    Mickster Formula Junior

    Oct 24, 2015
    608
    Sweden
    Full Name:
    Mikael Andersson
    #3 Mickster, Nov 8, 2017
    Last edited: Nov 8, 2017
    I used this when I repainted the oil reservoir. The hardest part was getting the old paint off. The surface needs to be quite rough for the paint to ”bite” properly.
    Also available in red (Google around to find locally), and I know a few guys have tried it with good result.
    You’ll find a good ”how to” on this web page: https://aldousvoice.com/2012/09/11/ferrari-360-disareator-refurbishment/ Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login
     
    Zcobra1 and whatheheck like this.
  4. Slc2nd

    Slc2nd Rookie

    Aug 28, 2017
    6
    Roswell Ga
    Full Name:
    Stanton Clark
    #4 Slc2nd, Nov 9, 2017
    Thanks Mickster looks like a nice job. I bought the red VHT paint from my local dealer here in Atlanta. I think removing the manifolds would be a big job from what I have been told, so hoping I can tape everything off and paint in place and get a decent result. If anyone had done this I'd love to hear how it went. Thanks again
     
  5. Dave rocks

    Dave rocks F1 World Champ
    BANNED

    Nov 23, 2012
    16,047
    Orchard Park, NY
    Full Name:
    Dave Lelonek
    #5 Dave rocks, Nov 9, 2017
    Not a chance. It needs to be fully disassembled to do the job correctly. Also, you need to bake the parts to get the wrinkle effect. That should be done after a short flash. Also, these coatings take a good amount of time to harden so they will be soft for a while so you need to be very careful.
     
  6. Keith360

    Keith360 Formula Junior

    Feb 6, 2015
    570
    Santa Barbara County
    Full Name:
    Keith Williams
    #6 Keith360, Nov 9, 2017
    I've had good luck with the VHT Wrinkle Red without baking them in a oven. Their red paint is pretty close to the OEM. My advice is to paint as evenly as possible and don't put so much on that it runs. Even coat means even finished product. When applying it may look like its not working, just give it time. Better to do it in warm weather (70-75F) and no breeze. If it looks like the wrinkle is only happening is spotty area, do not/do not/do not apply more paint.
     

    Attached Files:

  7. ATLSIGNGUY

    ATLSIGNGUY Karting

    Mar 10, 2017
    78
    Atlanta
    Full Name:
    PJ Houser
    #7 ATLSIGNGUY, Nov 9, 2017
    Just a friendly note.... Don't take your 360 to FoA for a basic service type job, call my independent Ferrari certified tech, he is used by many around Atlanta. Heroes great work, uses correct parts, and is cheaper, plus a great guy.

    Ron @ Sports Car Service in Tucker.
    404-435-6760
     
  8. Dave rocks

    Dave rocks F1 World Champ
    BANNED

    Nov 23, 2012
    16,047
    Orchard Park, NY
    Full Name:
    Dave Lelonek
    #8 Dave rocks, Nov 9, 2017
    Here is a photo of VHT against and OEM manifold - the color is not close at all. The VHT is too orange. Is it bad? No, but it's just not factory correct and don't try to do a touch up with it as it will never match. The VHT is on my 355 plug cover the part that says "Ferrari" is a 360 OEM finish.


    Image Unavailable, Please Login
     
    RossoC360 likes this.
  9. Mickster

    Mickster Formula Junior

    Oct 24, 2015
    608
    Sweden
    Full Name:
    Mikael Andersson
    #9 Mickster, Nov 10, 2017
    I’ve never seen the two side by side before. You’re right - there’s quite a difference...
     
  10. sierra055

    sierra055 Formula Junior
    Silver Subscribed

    Sep 25, 2016
    362
    Melbourne, AU
    Full Name:
    Marshall
    #10 sierra055, Nov 10, 2017
    There are some powders that also come quite close to the factory colour and finish, but also obviously require disassembly and baking. Image Unavailable, Please Login
     

Share This Page