330 GT (Series 2) parcel tray measurements please

Can someone with a 330 Gt (series 2) please take some measurements of the rear parcel tray speaker grills for me. My car no longer has the original parcel tray but I want to replicate the factory specifications as much as possible.

I assume from photos that the rear parcel tray is in leather with "speaker grills" consisting of punched holes in the leather.

I'm interested in the diameter of these holes (could be carefully measured with the blunt end of a drill bit) and the measurements to locate these holes. I have attached an image of the measurements I'm looking for.

If anyone has any further photos of their original parcel tray or any advice then that would also me appreciated.

(Photo courtesy of www.330gt.com)

Image Unavailable, Please Login

 

I may be able to help you.
Is the car yours. ch # please Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login ??

 

Hi Daytonaman

Yes the car is mine. Chassis number 9187. I purchased it earlier this year and I also have 400i and a 308 GT4 if you are trying to fill in the blanks on my other posts on this forum.

9187 has never been restored and is very original apart from the paint colour and a few details like the parcel tray. I have radio holes in the dash so I have purchased the correct 1966 radio to cover those and of course I need to deal to the parcel tray for both the speaker installation and to return the car closer to original.

I see you live in Australia? I normally reside in Darling Point, Sydney but my 400 & 330 live in NZ (where I am at the moment).

That tool looks like a very good approach to this problem. Did you hand drill that steel sheet on a drill press or do you have access to a CNC machine?

Guessing you also have the measurements to locate the tool?

Thanks
Thomas

P.S attached is a photo of the car last time I was out before lockdown


Image Unavailable, Please Login

 

Hi Thomas would be great to catch up
email
[email protected]
0428486738

 

See http://www.parrotbyte.com/kbc/ferrari/330gt/PackageShelf.htm on how I replaced mine.
Regards, Kerry

 

Howie - that you in the picture )))))

 

yours truly !

 

The hole size is 5/32". Here are location dimensions from an original package shelf. Note the thin foam between the leather and fiberboard panel.
Image Unavailable, Please Login Image Unavailable, Please Login

 

I have a 330 GT interin car SN 7323 - the holes are not for speakers - there is a fan under there for demisting the rear window

 

so same than as at the 250 GT/E

 

S1 and S2 different
S2 definately speakers both sides
S2 had heated rear screen element

 

Thank you everyone for your replies and advice. Especially to Kerry for the measurements. I have also been kindly offered a punch template form another forum member which will be a huge help to my project.

I have removed my parcel tray to find that my card is original but it has been covered in cheap Vinyl with a leather look grain though it. I will steam the card to flatten but I'm now after a supplier of there correct leather. Another Fchat member has suggested I should be sourcing Connolly Vaumol. As my dash, tunnel and console is all black I assume the parcel tray would also have been black?

The other thing I'm not 100% sure bout is the piping around the rear edge. I have seen that in many of Kerry's photos. It appears this piping is in the same colour leather as the parcel tray and attached to outer edge from the underside? This forms a trim between this edge of the parcel tray and the white vinyl trim I have under the rear window?

Attached is a few photos of my parcel tray and the white vinyl trim.

Thanks
Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login

 

Scratch that, I have just found Kerry's link which explains the piping section around the back of the parcel tray.... Now to find leather and I can get my. work started.

Thank you everyone