Some TLC for my QV | Page 12 | FerrariChat
Buy

Some TLC for my QV

Discussion in 'Mondial' started by afterburner, Mar 25, 2015.

This site may earn a commission from merchant affiliate links, including eBay, Amazon, Skimlinks, and others.

Page 12 of 33
  1. afterburner

    afterburner F1 Rookie
    Silver Subscribed

    Jun 20, 2008
    3,470
    Switzerland
    Full Name:
    Urs STEMMLER
    #276 afterburner, May 24, 2021
    Front section clean-up and repairs. Note the two humps for clearance of the radiator fan motors and the inclined surfaces fading of the side/rear of the car. This is an exit air guide guiding the air sidewise away from the centre section, which has blocked exit on the bonnet.
    This deviates the air away from the centreline section of the car and over the front wing, helping reduce front end lift.
    Image Unavailable, Please Login Image Unavailable, Please Login
    Battery-cover side repairs
    Image Unavailable, Please Login

    Image Unavailable, Please Login

    Some holes needed to be filled and cracks repaired
    Image Unavailable, Please Login
    Parts painted
    Image Unavailable, Please Login Image Unavailable, Please Login
     
  2. afterburner

    afterburner F1 Rookie
    Silver Subscribed

    Jun 20, 2008
    3,470
    Switzerland
    Full Name:
    Urs STEMMLER
    #277 afterburner, May 24, 2021
  3. ronfrohock

    ronfrohock F1 Rookie
    Owner Rossa Subscribed

    Aug 16, 2004
    4,156
    MA
    Full Name:
    Ron Frohock
    #278 ronfrohock, May 24, 2021
  4. afterburner

    afterburner F1 Rookie
    Silver Subscribed

    Jun 20, 2008
    3,470
    Switzerland
    Full Name:
    Urs STEMMLER
    #279 afterburner, May 24, 2021
    Thanks Ron!
     
  5. afterburner

    afterburner F1 Rookie
    Silver Subscribed

    Jun 20, 2008
    3,470
    Switzerland
    Full Name:
    Urs STEMMLER
    #280 afterburner, May 24, 2021
    Fuel filler neck gasket as removed
    Image Unavailable, Please Login Image Unavailable, Please Login
    Cleaned up and silicon paste treated
    Image Unavailable, Please Login
    Gas pedal cover as removed
    Image Unavailable, Please Login
    Image Unavailable, Please Login
    part number on a vacuum forming:
    Image Unavailable, Please Login

    cracks around the mounting holes

    Image Unavailable, Please Login

    Repairs
    Image Unavailable, Please Login
    repaired
    Image Unavailable, Please Login
    and repainted - as new!
    Image Unavailable, Please Login
     
  6. afterburner

    afterburner F1 Rookie
    Silver Subscribed

    Jun 20, 2008
    3,470
    Switzerland
    Full Name:
    Urs STEMMLER
    #281 afterburner, May 24, 2021
  7. afterburner

    afterburner F1 Rookie
    Silver Subscribed

    Jun 20, 2008
    3,470
    Switzerland
    Full Name:
    Urs STEMMLER
    #282 afterburner, May 24, 2021
    HVAC restoration - the elephant in the room > heater leaking, fresh air flap inop... and what else once it's opened up? Here how it looked removed:
    Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login
    The fan motor looks tired - and see the rust...
    Image Unavailable, Please Login
    Heater core has badly leaked. My guess is that some cheapskate used water instead of proper coolant...bust tubes:
    Image Unavailable, Please Login
    drain plate inside the housing has corroded away
    Image Unavailable, Please Login
    Image Unavailable, Please Login
     
  8. afterburner

    afterburner F1 Rookie
    Silver Subscribed

    Jun 20, 2008
    3,470
    Switzerland
    Full Name:
    Urs STEMMLER
    #283 afterburner, May 25, 2021
  9. afterburner

    afterburner F1 Rookie
    Silver Subscribed

    Jun 20, 2008
    3,470
    Switzerland
    Full Name:
    Urs STEMMLER
    #284 afterburner, May 25, 2021
  10. afterburner

    afterburner F1 Rookie
    Silver Subscribed

    Jun 20, 2008
    3,470
    Switzerland
    Full Name:
    Urs STEMMLER
    #285 afterburner, May 25, 2021
  11. afterburner

    afterburner F1 Rookie
    Silver Subscribed

    Jun 20, 2008
    3,470
    Switzerland
    Full Name:
    Urs STEMMLER
    #286 afterburner, May 25, 2021
    The exit flap is in metal - the foam gone
    Image Unavailable, Please Login
    cleaned up and foam cut
    Image Unavailable, Please Login
    done
    Image Unavailable, Please Login
    Replacement heater core as removed - lots of bent/blocked fins, pressure tests ok
    Image Unavailable, Please Login
    There is a foam sealer strip on the top front edge:
    Image Unavailable, Please Login
    Cleaned up and masked:
    Image Unavailable, Please Login
    repainted end plates with zinc paint and all fins straightened and cleaned out, new rubber gasket

    Image Unavailable, Please Login Image Unavailable, Please Login
     
  12. afterburner

    afterburner F1 Rookie
    Silver Subscribed

    Jun 20, 2008
    3,470
    Switzerland
    Full Name:
    Urs STEMMLER
    #287 afterburner, May 25, 2021
    Evaporator with end sections bead blasted, pressure tested, but tons of bent fins:
    Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login
    Expansion valve
    Image Unavailable, Please Login
    inlet pressure hose tags

    Image Unavailable, Please Login
    Tags removed
    Image Unavailable, Please Login
    flattened and ready to be refitted onto the new hose - invisible originality! Image Unavailable, Please Login
    Evaporator masked
    Image Unavailable, Please Login
     
  13. afterburner

    afterburner F1 Rookie
    Silver Subscribed

    Jun 20, 2008
    3,470
    Switzerland
    Full Name:
    Urs STEMMLER
    #288 afterburner, May 25, 2021
  14. afterburner

    afterburner F1 Rookie
    Silver Subscribed

    Jun 20, 2008
    3,470
    Switzerland
    Full Name:
    Urs STEMMLER
    #289 afterburner, May 25, 2021
  15. afterburner

    afterburner F1 Rookie
    Silver Subscribed

    Jun 20, 2008
    3,470
    Switzerland
    Full Name:
    Urs STEMMLER
    #290 afterburner, May 25, 2021
    Core pack fitted to housing base
    Image Unavailable, Please Login Image Unavailable, Please Login
    Fan assembly - new motor, old drums and rubber dampers. Rivets had be drilled open and need replacement with bolts.

    Image Unavailable, Please Login
    there's a grommet at the cable passage:
    Image Unavailable, Please Login
    new motor's cable were shorter than original - lengthened and original colors used at the plug side so it turns the right way round...
    Image Unavailable, Please Login
    Fan assembly completed
    Image Unavailable, Please Login
    and fitted to the base

    Image Unavailable, Please Login Image Unavailable, Please Login
     
  16. afterburner

    afterburner F1 Rookie
    Silver Subscribed

    Jun 20, 2008
    3,470
    Switzerland
    Full Name:
    Urs STEMMLER
    #291 afterburner, May 25, 2021
    There is an inconvenient wiring setup for the evaporator temp sensor, which goes directly from the relay set through the top housing:

    Image Unavailable, Please Login
    Image Unavailable, Please Login

    This means you need to have those relays dangling with the top housing. Very impractical for assembly and potential trouble shooting.
    I added a plug (yes, another potential source of trouble) but really convenient for reassembling the HVAC and refitting it to the car:

    Image Unavailable, Please Login
    Now, the relay set can be fitted once the rest is in place - no ripping cables out while fitting the HVAC. Sensor testing while it's convenient:

    Image Unavailable, Please Login
    Image Unavailable, Please Login
    Checks out fine. Bleed air sensor:
    Image Unavailable, Please Login

    So reassembly continues with the exit air section; parts ready:

    Image Unavailable, Please Login
    completed, with previously restored power transistor and checked vacuum actuator

    Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login
     
  17. afterburner

    afterburner F1 Rookie
    Silver Subscribed

    Jun 20, 2008
    3,470
    Switzerland
    Full Name:
    Urs STEMMLER
    #292 afterburner, May 25, 2021
    Top section with intake flaps is next. Those flaps have surrounding gaskets which were broken:
    Image Unavailable, Please Login
    Cleaned up and new gaskets made
    Image Unavailable, Please Login
    Parts ready, with brackets repainted and vacuum actuators checked
    Image Unavailable, Please Login
    Assembled top section
    Image Unavailable, Please Login
    Image Unavailable, Please Login
    Image Unavailable, Please Login
    Image Unavailable, Please Login
    Note the little centre stop that prevents the fresh air flap from completely closing - it will always allow a minimal external air enter the car even when AC is selected (internal air circulation)
    Image Unavailable, Please Login
    Hypoxia prevention???
    Image Unavailable, Please Login
    Image Unavailable, Please Login
     
  18. afterburner

    afterburner F1 Rookie
    Silver Subscribed

    Jun 20, 2008
    3,470
    Switzerland
    Full Name:
    Urs STEMMLER
    #293 afterburner, May 25, 2021
    Final assembly of the unit's top and bottom sections include a bead of Seal'n'Peel on all touching interfaces, which do have a groove and tongue section, to prevent air leaks and rattles:

    Image Unavailable, Please Login

    That includes the external footwell outlets - and don't forget to connect and route the vacuum hoses. Easy now, a pain later:

    Image Unavailable, Please Login
    Image Unavailable, Please Login
    Evaporator sensor gets sealed in too
    Image Unavailable, Please Login
    I built a water tap vacuum pump to test the flaps via the centre console control box before installing it into the car
    Image Unavailable, Please Login
    Image Unavailable, Please Login
    It all worked perfectly.

    That's what your control box should show electrically:

    Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login
     
  19. afterburner

    afterburner F1 Rookie
    Silver Subscribed

    Jun 20, 2008
    3,470
    Switzerland
    Full Name:
    Urs STEMMLER
    #294 afterburner, May 25, 2021
  20. afterburner

    afterburner F1 Rookie
    Silver Subscribed

    Jun 20, 2008
    3,470
    Switzerland
    Full Name:
    Urs STEMMLER
    #295 afterburner, May 25, 2021
    2cam likes this.
  21. 2cam

    2cam Formula Junior

    Aug 28, 2014
    749
    Austin, Texas
    Full Name:
    MikeS
    #296 2cam, May 25, 2021
    I'm continually impressed by your commitment to the project and ability! VERY cool!

    2cam
     
  22. afterburner

    afterburner F1 Rookie
    Silver Subscribed

    Jun 20, 2008
    3,470
    Switzerland
    Full Name:
    Urs STEMMLER
    #297 afterburner, May 25, 2021
    Thanks Mike! More to come :cool: till the car is back on the road.
     
  23. afterburner

    afterburner F1 Rookie
    Silver Subscribed

    Jun 20, 2008
    3,470
    Switzerland
    Full Name:
    Urs STEMMLER
    #298 afterburner, May 26, 2021
    Main wiring loom restoration - front fire wall to centre tunnel - engine bay - trunk. As removed:

    Image Unavailable, Please Login
    Some detail shots:
    Image Unavailable, Please Login
    Rock-hard sheaths, oil, tape ....
    Image Unavailable, Please Login
    All cleared sections secured with cable ties to keep the junctions correctly located
    Image Unavailable, Please Login

    engine bay connectors...

    Image Unavailable, Please Login

    all removed

    Image Unavailable, Please Login
    cleaning
    Image Unavailable, Please Login
    before/after
    Image Unavailable, Please Login
    re-color coding after cleaning
    Image Unavailable, Please Login Image Unavailable, Please Login
     
  24. stoked_7

    stoked_7 Karting
    Rossa Subscribed

    Nov 9, 2020
    215
    USA
    #299 stoked_7, May 26, 2021
    Fantastic work, can't wait until you have this back on the road.

    What paint are you using for the black interior plastics like the pedal cover you repainted?
     
  25. afterburner

    afterburner F1 Rookie
    Silver Subscribed

    Jun 20, 2008
    3,470
    Switzerland
    Full Name:
    Urs STEMMLER
    #300 afterburner, May 26, 2021
    Ignition multi-plugs cleaning and re-insulation on damaged zones
    Image Unavailable, Please Login
    Image Unavailable, Please Login
    retaped and ready

    Image Unavailable, Please Login

    Next lower engine bay wiring loom cleaned - main power supply bypass visible:
    Image Unavailable, Please Login
    retaped
    Image Unavailable, Please Login
    Upper engine bay loom as removed
    Image Unavailable, Please Login
    Some damage detail - often caused by hardened sheathing and dried out rubber boots
    Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login
     
Page 12 of 33

Share This Page