Wiring for the 355 blower timing actuator

I got some teeth broke off the gear in the blower timing actuator 63307100. When glued the teeth back in-place I learned the actuator not spinning at all with the engine and blower/AC on.

The power to the actuator is coming on Black and Red wires.

Image Unavailable, Please Login
The actuator motor itself shows connectivity OK between both connectors on the electrical motor meaning the wires in the motor are OK and not burnt off.

Incoming power to the actuator motor is coming to the Red and White-Black wires.
Image Unavailable, Please Login

There is no voltage coming to the Red/White-black wires when the engine is running and AC is blowing to the actuator. In the climate-control panel the wires in the connector are thinner and different color scheme.

There is 30A fuse in the front trunk on the RH side of the blower radiator box wall and that fuse is for the blower itself (which is working) and for the AC pump clutch (and the AC is working).

The internal/external air door is also not working/kept always open.

The fan changing its' speed reacting on the fan speed knob position change. The button STOP on the climate control panel stops the AC as it should.

Where the voltage to the blower actuator is coming from?

 

It's not the gear. My glued gear is OK. The actuator is not spinnig no power to it. And I already got a 3-D printed gear.

 

I already have replace the draveshaft on the fresh air flap to the LH engineering one many years ago. Appearing none of both actuators get power to operate.

Seems the power for the flap coming from pins #22/23 of the connector 10520 and the power for the timing actuator to #18/19 it's not showing on the diagram what is coming to those pins from the other end?

 

Correct. The problem is when changing the airflow direction knob no voltage comes to red/black pins.

And yes. When the ignition is on there is +5V on the yellow wire pin.

 

The climate-control ECU or Motronic that controls the engine?

The airfan fuse 10A in the passenger foot-well is OK.

 

SOLVED.

A great mind thinks alike. When you was typing it up on the other end of the Earth I was opening the front trunk and turning the Ground switch off for the car battery.

Turned the ground switch back up after 5" and both actuators are working. Original glueded by an epoxy glue gear is spinning.

Time to glue back together the actuator box leave it overnight and tomorrow morning eveything will be back in place and now it's a time for a 6-pack.

Big relief.

 

Thoughts from the troubleshooting:
- When the timing actuator gear teeth broke off the actuator kept spinning and the position sensor kept reporting the same position of the gear. The ECU based on the feedback from the sensor cut off the power to both actuators to not to burn off the electrical motor for the timing actuator. The power reset for the ECU flushed the ECU memory.

 

I think that might be related on which setting you keep the airflow direction knob. I keep it to AUTO 99% of the time so to my understanding it changes the direction of airflow constantly or often if you have the knob to one of the manual positions changing it rarely the original gear might last longer.

I am looking forward to see for how long the glued original gear would last? I already have bought a 3-D printed replacement as mentioned earlier in this chat.

 

For the LHD cars it's a pain in the butt as well. With a little advantage of a non-presence of the steering wheel column and the pedals.

I didn't remove anything to get to the actuator but the space is so tight (and I needed to hold a flashlight with my LH) doing the work RH only. The only working position was lying on my RH ribs. Tightening the screws at the end so the actuator is not loose was a real pain. I was able to achieve it only by sitting on the RH seat moved it all the way fwd.

Also a FYI if you take out the actuator and try to see how it's workng hanging in the air my actuator shaft was turning back and forth a bit then returning to the same position regarding which airflow direction I was setting on the climate control panel. Even after I had put it back into place. Another battery switch reset did the memory flush again to the climate control ECU and it started working as intended. I think when you operate it while taken out the ECU detects the actuator motor takes less electrical power than when loaded and returns it back to the some "default" position regardless of a command from the control knob. And why it's keeping doing so when I had put the actuator back in-place - I think the logic is once the ECU detects any deviation from the actuator from the expected responses - it's halting the operation until a human intervention with a confirmation all been addressed in a form of the power reset.