Wanted - 250 Inside spark plug bearing | FerrariChat
Buy

Wanted 250 Inside spark plug bearing

Discussion in 'Ferrari Parts & Collectibles' started by Bertocchi, Dec 16, 2021.

This site may earn a commission from merchant affiliate links, including eBay, Amazon, Skimlinks, and others.

  1. Bertocchi

    Bertocchi Formula 3
    Consultant

    Jan 28, 2004
    2,326
    Austin, Texas
    Full Name:
    David Castelhano
    #1 Bertocchi, Dec 16, 2021
    I am rebuilding the water pump from a 1959 Ferrari 250 PF Coupe and am having difficulty locating a new replacement ball bearing. It is classified as a deep groove bearing open on both sides.
    Dimensions;
    15 mm I.D.
    37 mm O.D.
    10 mm thickness (9 will do)

    Markings say it is a Fafnir 103K I have cross referenced it to a SKF 98202 which is no longer made.

    Any help would be deeply appreciated. I'm looking for a reliable bearing supplier in general, ideally someone with a stash of older bearings.
     
  2. Edward 96GTS

    Edward 96GTS F1 World Champ
    BANNED Silver Subscribed

    Nov 1, 2003
    11,097
    #2 Edward 96GTS, Dec 16, 2021
    title correct?
     
  3. Steve Magnusson

    Steve Magnusson Two Time F1 World Champ
    Lifetime Rossa

    Jan 11, 2001
    26,854
    30°30'40" N 97°35'41" W (Texas)
    Full Name:
    Steve Magnusson
    #3 Steve Magnusson, Dec 16, 2021
    This source shows having 98202 (15x37x9) in stock:

    https://www.123bearing.com/bearings-98202#container-tech-schema

    but no idea if SKF or Chinese knock off. Another option would be to use an SKF 6003 17x35x10 and make an ID and OD spacer if the shoulders on the housing and shaft are big enough to still contact the bearing races (and not just the spacers).
     
  4. huidu

    huidu Rookie

    Jun 9, 2023
    2
    Full Name:
    hui du
    #4 huidu, Jun 9, 2023
    I've had the same problem before, but my car doesn't share your brand, but I use Single row angular contact ball bearings 7210-B-TVP-P5-UL, very good, hope you can help.The characteristic of double row angular contact ball bearings is that they can bear the combined load of radial and axial loads at the same time, and limit the axial displacement of the shaft in both directions. Compared with two-way thrust ball bearings, this bearing has a higher limit speed, a contact angle of 32 degrees, good rigidity, and can withstand large overturning moments.
    Take it if you can use it.https://en.tradebearings.com/7210_B_TVP_P5_UL-395008.html
     
  5. loflyer47

    loflyer47 Formula Junior

    Sep 28, 2004
    362
    Phila. area, Pa.
    Full Name:
    Ben
    #5 loflyer47, Jun 9, 2023
    I too have an inside plug car from 1958. Do have a number of various bearings, gaskets, etc I’ve accumulated over the years. I’ll check to see what I have. I do have a number of various gaskets, rings, other bearings, extra parts. Do also have a couple of extra original brake drums, I believe front left and right…
    Various mousetrap springs for 4 cylinder and 12 cylinder motors. Also some Lamprey stuff.
    I’ll check on that bearing for you…
     
  6. miketuason

    miketuason F1 World Champ
    Owner Silver Subscribed

    Feb 24, 2006
    15,814
    Cerritos, CA.
    Full Name:
    Mike
    #6 miketuason, Jun 9, 2023
    I’ve never heard of spark plug bearing, what is it?
     
  7. Steve Magnusson

    Steve Magnusson Two Time F1 World Champ
    Lifetime Rossa

    Jan 11, 2001
    26,854
    30°30'40" N 97°35'41" W (Texas)
    Full Name:
    Steve Magnusson
    #7 Steve Magnusson, Jun 9, 2023
    Did you forget to include the "joke" emoji?
     
  8. Bertocchi

    Bertocchi Formula 3
    Consultant

    Jan 28, 2004
    2,326
    Austin, Texas
    Full Name:
    David Castelhano
    #8 Bertocchi, Jun 10, 2023
    Thank you for your response. We were able to find a bearing in the UK.
    I’m now restoring an outside spark plug 250 PF Coupe and will keep you in mind if I need something unusual
     

Share This Page