PIX | FerrariChat

PIX

Discussion in '308/328' started by Gliozzi, Jun 21, 2011.

This site may earn a commission from merchant affiliate links, including eBay, Amazon, Skimlinks, and others.

  1. Gliozzi

    Gliozzi Karting

    Joined:
    May 6, 2011
    Messages:
    84
    Location:
    Oakdale Calif.
    Full Name:
    Bob
    Last edited by a moderator: Sep 7, 2017
    Gliozzi, Jun 21, 2011
    #1
  2. maurice70

    maurice70 F1 Rookie

    Joined:
    Jan 25, 2004
    Messages:
    4,334
    Location:
    Sydney
    Full Name:
    maurice T
    Of?
     
    maurice70, Jun 21, 2011
    #2
  3. viphoto

    viphoto Formula Junior

    Joined:
    Sep 11, 2010
    Messages:
    264
    Location:
    Carlsbad, CA
    Full Name:
    Mark
    Looks like the spring washer behind the outer cam Drive Bearing...Do I win?
     
    viphoto, Jun 21, 2011
    #3
  4. lostbowl

    lostbowl Formula 3

    Joined:
    Apr 30, 2009
    Messages:
    1,246
    Location:
    Michigan
    Full Name:
    Tom
    Now I have to check the parts manual because I don't remember having a distance or spring washer on mine. ???????????? Lost
     
    lostbowl, Jun 21, 2011
    #4
  5. Dr Tommy Cosgrove

    Dr Tommy Cosgrove Three Time F1 World Champ Owner Rossa Subscribed

    Joined:
    May 4, 2001
    Messages:
    36,614
    Location:
    Birmingham, AL
    Full Name:
    Tommy
    cock ring?
     
    Dr Tommy Cosgrove, Jun 21, 2011
    #5
  6. flyngti

    flyngti Formula 3

    Joined:
    Jul 16, 2009
    Messages:
    1,257
    Location:
    Snohomish, WA
    Full Name:
    Eric L
    Ouch. Thin and sharp.
     
    flyngti, Jun 21, 2011
    #6
  7. ramosel

    ramosel Formula 3

    Joined:
    Sep 11, 2004
    Messages:
    1,237
    Location:
    Meadow Vista, CA
    Full Name:
    R Moseley
    Last edited by a moderator: Sep 7, 2017
    ramosel, Jun 21, 2011
    #7
  8. Ferraripilot

    Ferraripilot F1 World Champ Owner Project Master

    Joined:
    May 10, 2006
    Messages:
    17,937
    Location:
    Atlanta
    Full Name:
    John!
    +1
     
    Ferraripilot, Jun 21, 2011
    #8
  9. Gliozzi

    Gliozzi Karting

    Joined:
    May 6, 2011
    Messages:
    84
    Location:
    Oakdale Calif.
    Full Name:
    Bob
    Yes You DO
     
    Gliozzi, Jun 21, 2011
    #9
  10. lostbowl

    lostbowl Formula 3

    Joined:
    Apr 30, 2009
    Messages:
    1,246
    Location:
    Michigan
    Full Name:
    Tom
    Looked in the parts book and I see a washer used on the cars with an exterior seal but I don't see anything for the engine with the seal inside. Mine is an 82 and I just changed the bearings and seals and there were no spring washers in either side and it doesn't appear as though anything was touched by bthe PO except the valve settinga and that's a whole other chapter. Lost
     
    lostbowl, Jun 22, 2011
    #10
  11. viphoto

    viphoto Formula Junior

    Joined:
    Sep 11, 2010
    Messages:
    264
    Location:
    Carlsbad, CA
    Full Name:
    Mark
    FWIW My 79 has the internal seal and behind the outer sealed bearing was one of these washers. Not sure what it would really do except distance the bearing from the circlip....
     
    viphoto, Jun 22, 2011
    #11
  12. lostbowl

    lostbowl Formula 3

    Joined:
    Apr 30, 2009
    Messages:
    1,246
    Location:
    Michigan
    Full Name:
    Tom
    I would have to guess that the spring washer took up tolerance that Luigi couldn't obtain without CNC. I'm not concerned other than why the parts manaual doesn't show them. Then again I do come across variations in these posts. Lost
     
    lostbowl, Jun 22, 2011
    #12
  13. Jedi

    Jedi Moderator Moderator Lifetime Rossa Owner

    Joined:
    Mar 18, 2008
    Messages:
    32,352
    Location:
    Seattle Area
    Full Name:
    Dave
    O
     
    Jedi, Jun 22, 2011
    #13

Share This Page