13" 458 Spider (Gear Box Issue?)

I'm not sure if I understand your situation correctly.

When you put the car to "manual shifting", the shifts are harder and you can feel them a little bit on your neck.Also when you upshift near the readline you will note a little sound between shifts.
I have not noticed that little sound(squeak) on downshifts.Can you note that squeak easily?
If your dealer is close to you I will recommend to go for a general review to your car.
Keep us informed.

Good luck!

 

I have heard the noise in almost all 458 I have driven with. Get it checked but should be normal

 

My '11 lets out a mild squeak once in awhile, very rarely. Shifting is more aggressive in race mode. All this is normal.

 

Don't mess with it. Take it to the dealer.

 

That is not normal. Agree... take it to the dealer.

 

+458

 

Try this: When you shift up or down, try to flick the paddle faster, very fast. This way it won't jerk when up-shift and the down-shift will sound like gun shot.

 

I wouldn't trouble shoot or experiment with it. It could make matters worse. Take it to your dealer.

 

Stupid question. But are you lifting off the accelerator when shifting?

 

FYI, automatic will wear out your clutch faster.


Sent from my Ferrari F430 & 360

 

The squeek happens on upshifts, it is more pronounced on 2010-2011 cars.

 

Let us know. Thanks.

 

For Ferrari cars, if you are out of warranty and the car has a problem, do dealers give free estimate to repair? Last time I had a Mercedes SUV, the repair would cost $2,000 but the estimation alone was already $700. Even if I ended up repairing it in the dealer, I still had to pay the $700 + $2,000.

 

Not a red light gear box error here but I got the catalytic temp not plausible once some time ago,I talked with some friends that had the same and all of us have opened the engine compartment after a drive,then started the car again and thats the momment when it appears and in a few second went away.
Any of us had anexplanation for this,there is a mechanical reason?

 

Update as to where we are in the process:

1. Car came into us with the concerns the OP listed in his first post.
2. We were able to pull codes and confirm on a short test drive exactly what was stated.
3. We were able to confirm 1 hard fault ( P1977 ) and 4 ( P2440, P2442, P198E, P197D ) soft faults.
4. Following FNA direction we: Performed a Proxy alignment , Valve body clean, E-Diff Clean, Gear box re initialization, and a NCR cycle test.
5. Performing the above allowed us to confirm which component was performing as designed.
6. As P1977 was still current, that indicated that we would need to replace the SAP
( gearbox valve body ) which is supplied by FNA as a complete kit.

We have FNA technical approval for the repair as of this past Friday afternoon. We are now waiting on FNA warranty approval to order the kit.

Once the kit arrives, I would expect the car to be back on the road within 4-5 business days.

I will take pictures along the way and share as requested!

S



Intermittent initial codes:

P2440 : SECONDARY AIR INJECTION SYSTEM SWITCHING VALVE
STUCK OPEN (ABOVE MAXIMUM THRESHOLD)

P2442 : SECONDARY AIR INJECTION SYSTEM SWITCHING VALVE
STUCK CLOSED - (MAX) (ABOVE MAXIMUM THRESHOLD)

P198E : L2_SG10_BLOCKED_REAR_AXLE TOO LOW (REAR
BLOCKED AXLE RISK DURING SHIFT) (BELOW MINIMUM
THRESHOLD)

P197D : APP_SYNCHRO_4TH TOO HIGH (4TH GEAR CONTROL
FAULT CAN'T REACH) (ABOVE MAXIMUM THRESHOLD)

 

SAP Kit= Valve Body, the mechanical / electrical "control center" of the gear box will be replaced.

I attached a picture of an example ( NOT yours ) below,

S
Image Unavailable, Please Login