Replacing gauge cluster, can mileage be adjusted UP? | FerrariChat
Buy

Replacing gauge cluster, can mileage be adjusted UP?

Discussion in '360/430' started by RedNeck, Jul 28, 2018.

This site may earn a commission from merchant affiliate links, including eBay, Amazon, Skimlinks, and others.

  1. RedNeck

    RedNeck F1 World Champ
    Silver Subscribed

    Jul 8, 2016
    12,024
    The CSA
    Full Name:
    Me
    #1 RedNeck, Jul 28, 2018
    So instead of paying a ridiculous amount for 1 or 2 stepper motors, I found a killer deal on a complete cluster, and if I could just plug and play rather than taking 2 clusters apart to replace the stepper motors, that would be even better. Problem is, my car has 50k+ on it and the new cluster has less than 30. Don't want to show a mileage discrepancy, so would a dealer be able and willing to adjust mileage UP?

    Yes, I did search. Don't like the new search...too many hoops to jump through
     
  2. Qavion

    Qavion F1 World Champ
    Silver Subscribed

    Feb 20, 2015
    13,906
    Sydney
    Full Name:
    Ian Riddell
    #2 Qavion, Jul 28, 2018
    You could probably take the cluster to an instrument specialist and they could do if for you. Otherwise, you might have to get an electronics whiz to build a square wave generator which you can hook up to your speedo. Unfortunately, I think you'd have to limit the output frequency of the generator so that your speedo doesn't hit the end stop while the odometer is clicking over. This in turn will limit the speed at which your odometer will click over. Even at 200mph, your odometer would take 100 hours to add 20,000miles (and you'd have to keep a very careful eye on it to make sure you didn't go too far).

    http://www.learningaboutelectronics.com/Articles/Adjustable-square-wave-generator-circuit-with-a-555-timer.php
     
  3. tazandjan

    tazandjan Three Time F1 World Champ
    Lifetime Rossa Owner

    Jul 19, 2008
    39,037
    Clarksville, Tennessee
    Full Name:
    Terry H Phillips
    #3 tazandjan, Jul 28, 2018
    FAI in Costa Mesa can do it for you. They did it for a new cluster I had installed. Easy search.
     
    LorenzoR likes this.
  4. LorenzoR

    LorenzoR F1 Rookie
    Rossa Subscribed

    Sep 26, 2015
    3,141
    Sarasota Fl/Pittsburgh
    #4 LorenzoR, Jul 28, 2018
    I agree, FAI is very good at what they do
     
  5. RedNeck

    RedNeck F1 World Champ
    Silver Subscribed

    Jul 8, 2016
    12,024
    The CSA
    Full Name:
    Me
    #5 RedNeck, Jul 29, 2018
    Oh wow, I was electronics tech in a past life, so this would be no big deal. Guess I didn't realize it was so simple, since everything else electrical on this car is a pain, I figured that would be too. Thanks! Sounds like I will either have to send it out or build this, guess I just need to assess if it might not be less painful just to swap out the stepper motor..
     
    Qavion likes this.
  6. eric355

    eric355 Formula 3
    Silver Subscribed

    Nov 30, 2005
    1,215
    Toulouse (France)
    Full Name:
    Eric DECOUX
    #6 eric355, Jul 29, 2018
    No way to use that on a 360 cluster. Speed and mileage data are provided by the ABS ECU to the cluster through the CAN bus.

    Though, it is pretty easy to change the mileage by writting it directly in the EEPROM ...
     
  7. Qavion

    Qavion F1 World Champ
    Silver Subscribed

    Feb 20, 2015
    13,906
    Sydney
    Full Name:
    Ian Riddell
    #7 Qavion, Jul 29, 2018
    Sorry, I didn't realise how advanced these cars are. I assume you could plug a signal generator into the speed sensor cable on the gearbox, but you would have to leave your ignition on for a long time.

    On the earlier F355 only the tachometer signal goes through the ECU.

    Would the EPROM chip have to be removed from the board?
     
  8. eric355

    eric355 Formula 3
    Silver Subscribed

    Nov 30, 2005
    1,215
    Toulouse (France)
    Full Name:
    Eric DECOUX
    #8 eric355, Jul 30, 2018
    It can be done in situ with the EEPROM chip on the board.

    For the OP, an easy solution could be to copy the content of the EEPROM from the old cluster to the one of the new cluster, or to even easier to swap the EEPROMs ...
     
    Qavion likes this.
  9. RedNeck

    RedNeck F1 World Champ
    Silver Subscribed

    Jul 8, 2016
    12,024
    The CSA
    Full Name:
    Me
    #9 RedNeck, Jul 30, 2018
    If it's socketed, absolutely the easiest way. Supposed to be arriving today, haven't opened any up yet
     
  10. eric355

    eric355 Formula 3
    Silver Subscribed

    Nov 30, 2005
    1,215
    Toulouse (France)
    Full Name:
    Eric DECOUX
    #10 eric355, Jul 30, 2018
    Not socketed ! The EEPROM is soldered on the PCB.
    Not too difficult, it has a 8 pins SMD package.
     
  11. Mickster

    Mickster Formula Junior

    Oct 24, 2015
    608
    Sweden
    Full Name:
    Mikael Andersson
    #11 Mickster, Jul 30, 2018
    Yup! Used them and concur...
     
  12. RedNeck

    RedNeck F1 World Champ
    Silver Subscribed

    Jul 8, 2016
    12,024
    The CSA
    Full Name:
    Me
    #12 RedNeck, Jul 31, 2018
    Not bad, depending on the quality of the PCB itself. I had to change motors in a Chevy Silverado clusters and was lifting traces and lands with hardly any heat it was so bad. Hopefully this is a bit better. Cluster arrived today so will be testing soon.
     
  13. eric355

    eric355 Formula 3
    Silver Subscribed

    Nov 30, 2005
    1,215
    Toulouse (France)
    Full Name:
    Eric DECOUX
    #13 eric355, Jul 31, 2018
    Never had a problem with the PCB.
     
  14. CrazyMD

    CrazyMD Formula Junior

    Mar 10, 2012
    404
    Southern California
    #14 CrazyMD, Aug 2, 2018
    Pm me our shop can fix that for you.


    Sent from my iPhone using Tapatalk
     

Share This Page