360 - Anyone ever had their Tubi headers crack at the cylinder head? | Page 2 | FerrariChat
Buy

360 Anyone ever had their Tubi headers crack at the cylinder head?

Discussion in '360/430' started by Jaymac, Oct 25, 2025 at 12:31 PM.

This site may earn a commission from merchant affiliate links, including eBay, Amazon, Skimlinks, and others.

Page 2 of 2
  1. Jaymac

    Jaymac Formula 3
    Silver Subscribed

    Dec 18, 2020
    1,019
    New Hampshire
    Full Name:
    Jeremy McCurdy
    #26 Jaymac, Oct 26, 2025 at 3:40 PM
    The machine shop said they would put it in their oven to “bake it” before decking it (after the weld repairs), but I will be sure to ask the welder if they’re planning on doing that as part of their repair.
     
    Extreme1 likes this.
  2. Extreme1

    Extreme1 Formula 3

    Jun 27, 2017
    1,462
    Santa Clarita, CA
    #27 Extreme1, Oct 26, 2025 at 3:44 PM
    Replace the gasket. Do this right or you will be doing it again.
     
    jerbear27 likes this.
  3. flash32

    flash32 F1 Veteran

    Aug 22, 2008
    7,193
    Central NJ
    Full Name:
    Dominick
    #28 flash32, Oct 26, 2025 at 3:48 PM
    Tell them this is unacceptable for the price and you would.like.a replacement
     
  4. Extreme1

    Extreme1 Formula 3

    Jun 27, 2017
    1,462
    Santa Clarita, CA
    #29 Extreme1, Oct 26, 2025 at 4:00 PM
    Ok this is the same annealing process, just done in a different way.
     
    Jaymac likes this.
  5. andrejwolk1975

    andrejwolk1975 Karting

    Feb 28, 2020
    149
    Italy
    Full Name:
    Andrea M
    #30 andrejwolk1975, Oct 26, 2025 at 4:02 PM
    This is a perimetral failure not only a crack. Maybe this point was a ittle bit "recessed" than other 3 and thermal stress on a constant "stretch" caused this.
     
    EastMemphis likes this.
  6. Jaymac

    Jaymac Formula 3
    Silver Subscribed

    Dec 18, 2020
    1,019
    New Hampshire
    Full Name:
    Jeremy McCurdy
    #31 Jaymac, Oct 26, 2025 at 4:59 PM
    You’re right. Gaskets and OEM nuts in my cart on @Ricambi America . I’m going to call tomorrow and see if they’ll separate the set of OEM gaskets. The site will only allow a minimum of 8 gaskets.

    I can try, but I’m also not the original purchaser. I have the last owners installation receipt from the shop, but not the receipt for the parts themselves.
    Sounds like you have some welding knowledge. Do you think there could be any issues with rewelding this?

    The welder I found does this all the time on Harley’s due to vibration and flexing.
     
    Extreme1 and flash32 like this.
  7. andrejwolk1975

    andrejwolk1975 Karting

    Feb 28, 2020
    149
    Italy
    Full Name:
    Andrea M
    #32 andrejwolk1975, Oct 27, 2025 at 2:11 AM
    I think this work is doable but
    my suggestion is to remove the header:
    1) for a deep inspection on then inner side of the "crack" (debris incoming....who knows?);
    2) to verify the planarity of the installing surface of the header, maybe it was warped from the very beginning;
    3) to freely work on the header without concern and in the best possible way.
    If the header is ok on the inside, with no tendency to create debris, if you can (easily) recover the planarity of the piece I think that a professional welder could do the job easily.
    But as I said, first try to contact the producer: owners change the original headers for not having this kind of problems.....and you have had this.kind of problems!
    The F430 is a bit more "harsh" on the headers due the design, the 360 is more on the gently side with them.
     
Page 2 of 2

Share This Page