Search Results | FerrariChat
Buy

Search Results

This site may earn a commission from merchant affiliate links, including eBay, Amazon, Skimlinks, and others.

Search Again
Page 3 of 6
  1. paul 308
    Post

    Euro Carb'd 308 ignition curve

    The curve in my 1976 Euro carbed dry sump 308GTB handbook appears to plot distributor rpm against degrees of advance as follows: rpm...
    Post by: paul 308, Dec 27, 2007 in forum: 308/328
  2. paul 308
    Post

    Front caliper piston question

    If you're unlucky enough to have a seriously stuck piston, as I did, you can get them out but will have to replace with new. I very carefully...
    Post by: paul 308, Dec 27, 2007 in forum: 308/328
  3. paul 308
    Post

    Anyone looking for a Fiberglass body 308?

    if MREUS is right then its a '77 308, rhd on 76/77 UK plate. Strange that it should be wet sump though. I thought all UK rhd glass cars were dry...
    Post by: paul 308, Nov 18, 2007 in forum: 308/328
  4. paul 308
    Post

    Torqueing down a 308 head

    I'm 60! You don't know the meaning of pain in the mornings! Not sure about the sealant. I spent hours yesterday removing the stuff from a a...
    Post by: paul 308, May 15, 2007 in forum: Technical Q&A
  5. paul 308
    Post

    Torqueing down a 308 head

    I'm going to start by getting the cam cover gaskets in from Superformance and when time permits, get the deck and the air filter assembly off and...
    Post by: paul 308, May 15, 2007 in forum: Technical Q&A
  6. paul 308
    Post

    Another glass 308

    spare wheel bay cover panel/zipper cover missing
    Post by: paul 308, May 13, 2007 in forum: 308/328
  7. paul 308
    Post

    Torqueing down a 308 head

    I fear you may be right and I should leave well alone. By the way Birdman, I just did your carb float adjustment and tune up procedure and the...
    Post by: paul 308, May 13, 2007 in forum: Technical Q&A
  8. paul 308
    Post

    Torqueing down a 308 head

    Amen to all the above. However the belts and idlers were all replaced last year so, in the absence of tappet noise, I shall content myself with...
    Post by: paul 308, May 12, 2007 in forum: Technical Q&A
  9. paul 308
    Post

    Torqueing down a 308 head

    Logic says that tightening down the head shouldn't affect the valve clearances but I recently built a Vauxhall twin ohc engine with solid...
    Post by: paul 308, May 12, 2007 in forum: Technical Q&A
  10. paul 308
    Post

    Torqueing down a 308 head

    Thanks for the responses. Mine is a 2-valve engine so hopefully I can get away without the special tool. I know exactly what you mean about a...
    Post by: paul 308, May 11, 2007 in forum: Technical Q&A
  11. paul 308
    Post

    Torqueing down a 308 head

    Ah! thanks. Yes I'll give them a call. And there was me thinking I could just get a socket onto each nut and torque it up. Silly me! I guess...
    Post by: paul 308, May 10, 2007 in forum: Technical Q&A
  12. paul 308
    Thread

    Torqueing down a 308 head

    Having read recently that, on inspection, 308 head nuts have been found to be finger tight and being slightly concerned about pressurisation of...
    Thread by: paul 308, May 10, 2007, 35 replies, in forum: Technical Q&A
  13. paul 308
    Post

    Wobbly 308 a/c belt

    I replaced the missing bonding wire from the compressor to the engine and the problem has gone away. I can only assume that the wire was left off...
    Post by: paul 308, May 3, 2007 in forum: Technical Q&A
  14. paul 308
    Thread

    308 caliper rebuild

    I'm sure I've seen it somewhere but can anyone tell me the correct tightening torque to bolt the two halves of the front brake calliper together....
    Thread by: paul 308, Apr 26, 2007, 0 replies, in forum: Technical Q&A
  15. paul 308
    Post

    Wobbly 308 a/c belt

    The humidity is up today. Its been around 50 - 55% for the past couple of weeks but is now above 70%. Guess what - the ticking's gone. If it...
    Post by: paul 308, Apr 24, 2007 in forum: Technical Q&A
  16. paul 308
    Post

    Wobbly 308 a/c belt

    Thanks for the helpful suggestions, especially with the great pictures Robert. What a beautifully clean engine, must have been taken during a...
    Post by: paul 308, Apr 24, 2007 in forum: Technical Q&A
  17. paul 308
    Post

    Wobbly 308 a/c belt

    I suppose a quick and dirty way of determining whether its to do with the compressor/belt would be to cut off the compressor drive belt, which...
    Post by: paul 308, Apr 23, 2007 in forum: Technical Q&A
  18. paul 308
    Post

    Wobbly 308 a/c belt

    Thanks Mark. I'm pretty sure its not HT flyoff, it just sounds like it and, as I say, the ticking is in sync with the compressor belt rotation....
    Post by: paul 308, Apr 23, 2007 in forum: Technical Q&A
  19. paul 308
    Thread

    Wobbly 308 a/c belt

    '76 308GTB. a/c compressor drive belt appears to 'wobble', almost as though its rocking in the pulley V's each time the belt goes around. I...
    Thread by: paul 308, Apr 23, 2007, 14 replies, in forum: Technical Q&A
  20. paul 308
    Post

    308GTB 1979 break adjustment

    Its all here http://www.ferrarichat.com/discus/messages/256120/277302.html
    Post by: paul 308, Apr 15, 2007 in forum: Technical Q&A
Showing results 41 to 60 of 110 Next >
Search Again
Page 3 of 6