Search Results | FerrariChat
Buy

Search Results

This site may earn a commission from merchant affiliate links, including eBay, Amazon, Skimlinks, and others.

Search Again
Page 4 of 6
  1. paul 308
    Thread

    Greasing the 308GTB clutch release bearing

    The owner's manual tells me to grease the clutch release bearing (item 17) but not how. A search of the archives only reveals lightly greasing...
    Thread by: paul 308, Apr 14, 2007, 1 replies, in forum: Technical Q&A
  2. paul 308
    Post

    1976 308 - Update - Purchase

    That's a lovely car Joe, I hope you enjoy it as much as I enjoy mine. I have a UK spec fibre glass car with dry sump, chassis number 19965, so...
    Post by: paul 308, Apr 5, 2007 in forum: 308/328
  3. paul 308
    Post

    Who's got what?

    '76 308GTB, low mileage, GRP.
    Post by: paul 308, Mar 23, 2007 in forum: United Kingdom
  4. paul 308
    Post

    right hand drive

    Why a large part of the World (but by no means all) drives on the right amazes me. The rationale for driving on the left (the correct side) is...
    Post by: paul 308, Mar 23, 2007 in forum: Technical Q&A
  5. paul 308
    Post

    Weight of a 308 GTB dry sump glass car

    My November 1976 UK spec (rhd) 308GTB glass fibre bodied dry sumped car original handbook says 1265kg, 2788lbs dry weight. I have a CAR and...
    Post by: paul 308, Dec 2, 2006 in forum: 308/328
  6. paul 308
    Post

    Fiberglass 308 Questions

    My '76 fibreglass has the zip cover and a wheel retaining strap to hold it down. There is a metal bracket that the strap goes through on the...
    Post by: paul 308, Jul 15, 2006 in forum: 308/328
  7. paul 308
    Post

    Bolt on Silencers for a Tubi

    Rick Merlin Motorsport at Castle Combe do a selection of traps but you will have to fabricate a means of fitting them on so they don't fall...
    Post by: paul 308, Apr 10, 2006 in forum: Technical Q&A
  8. paul 308
    Post

    CAPICATORS FOR 308

    I'm not sure where the engine block to chassis ground is but look for a thick starter type cable somewhere between the engine/ transmission and...
    Post by: paul 308, Apr 5, 2006 in forum: Technical Q&A
  9. paul 308
    Post

    CAPICATORS FOR 308

    If its that bad I would suspect poor or non existent ground connection on the antenna and/or open circuit antenna connection. This might account...
    Post by: paul 308, Apr 4, 2006 in forum: Technical Q&A
  10. paul 308
    Post

    308 GT4 Fuel Pump

    Do they fit onto a shaft end and are there any witness marks where that shaft end might sit? Chances are you're right and they're a bearing and I...
    Post by: paul 308, Mar 25, 2006 in forum: Technical Q&A
  11. paul 308
    Post

    Help with restoring dead paint finish

    Having finally found the time and had a decent spell of weather to get on with trying out the Porter Cable orbital polisher, I'm pleased to report...
    Post by: paul 308, Aug 30, 2005 in forum: Technical Q&A
  12. paul 308
    Post

    where do i source reasonable 348 priced parts in the uk/europe???

    I don't think Superformance in Essex cover 348s but they may know who does. Try them on www.superformance.co.uk for contact info. Best of luck...
    Post by: paul 308, Jun 6, 2005 in forum: Technical Q&A
  13. paul 308
    Post

    Ever had your torque wrench tested?

    Birdman I use distilled water at standard temperature and pressure and then Subout Wright scales to weigh it out! I've just tightened a...
    Post by: paul 308, May 24, 2005 in forum: Technical Q&A
  14. paul 308
    Post

    Ever had your torque wrench tested?

    I check mine by clamping the square drive in a vice horizontally and hanging a (known weight) bucket from the end of the bar and filling it with...
    Post by: paul 308, May 20, 2005 in forum: Technical Q&A
  15. paul 308
    Post

    308 Suspension Restoration LOTS OF PICS

    Such a beautiful job. But how can you bear to take it out on the road?! And you even put the chalk numbers back on the arch covers! I assume...
    Post by: paul 308, Apr 14, 2005 in forum: Technical Q&A
  16. paul 308
    Post

    Can someone date these XWX's for me?

    Same tyre type but on a UK car, so they're not DOT marked. I have the same confusion as to whether this is week 02 of year 79, 89 or 99. Its...
    Post by: paul 308, Apr 5, 2005 in forum: Technical Q&A
  17. paul 308
    Post

    Blackening steel parts

    Thanks for the tips guys. Frosts Restoration Products in Lancashire do have a product, which is probably the same as the US sourced ones. I'll...
    Post by: paul 308, Feb 26, 2005 in forum: Technical Q&A
  18. paul 308
    Thread

    Blackening steel parts

    Anyone know a good home diy (safe) method of blackening exposed steel parts, bolts, nuts etc? I have found gun blueing products on US websites...
    Thread by: paul 308, Feb 25, 2005, 9 replies, in forum: Technical Q&A
  19. paul 308
    Post

    308 window cable...how many revolutions??

    Matt you might find the guys who contributed to this thread from the archives might be able to help if you PM/email them....
    Post by: paul 308, Feb 10, 2005 in forum: Technical Q&A
  20. paul 308
    Post

    308 window cable...how many revolutions??

    Matthew I've just done this job myself and the answer to your question is 3 3/4 turns - including the "loose" one that runs around the door...
    Post by: paul 308, Feb 4, 2005 in forum: Technical Q&A
Showing results 61 to 80 of 110 Next >
Search Again
Page 4 of 6