Search Results | FerrariChat
Buy

Search Results

This site may earn a commission from merchant affiliate links, including eBay, Amazon, Skimlinks, and others.

Search Again
Page 3 of 10
  1. derekw
    Post

    Cylinder not firing

    I would just hook up a 12VDC battery in piggy back directly to the ignition system to rule out the low voltage issue. If you have VR sensors (not...
    Post by: derekw, Jun 3, 2022 in forum: 308/328
  2. derekw
    Post

    V-12 Engine into 308 Build, over on Grassroots

    If it’s a lot of work to fit carbs, ignition, starter, then perhaps dye + heat+ pressure is enough to paint a picture of gasket and liner sealing....
    Post by: derekw, May 16, 2022 in forum: 308/328
  3. derekw
    Post

    V-12 Engine into 308 Build, over on Grassroots

    I think we’re going to see an X-ray machine on the back of that truck before the fat lady sings. Putting some dye in and retesting is little...
    Post by: derekw, May 16, 2022 in forum: 308/328
  4. derekw
    Post

    V-12 Engine into 308 Build, over on Grassroots

    I think we’re going to see an X-ray machine on the back of that truck edited the fat lady sings. Putting some dye in and retesting is little...
    Post by: derekw, May 16, 2022 in forum: 308/328
  5. derekw
    Post

    Outlaw 308

    Lots of banjo bolts online for £5-7. Also some nice looking polished aluminium header tanks not too expensive.
    Post by: derekw, May 15, 2022 in forum: 308/328
  6. derekw
    Post

    V-12 Engine into 308 Build, over on Grassroots

    I would try to run it for a few heat cycles. The expansion/ contraction might settle things and you would at least know if the gasket leak is...
    Post by: derekw, May 15, 2022 in forum: 308/328
  7. derekw
    Post

    Rear Brakes

    Mine had aluminium hex socket caps which rounded when trying to remove them. I found some stainless caps in case anyone needs some (£10/pair for...
    Post by: derekw, May 15, 2022 in forum: 308/328
  8. derekw
    Post

    V-12 Engine into 308 Build, over on Grassroots

    ... and dye for when it comes apart again?
    Post by: derekw, May 14, 2022 in forum: 308/328
  9. derekw
    Post

    V-12 Engine into 308 Build, over on Grassroots

    Put some UV or other dye into water and fill the block before pressure testing again. I’d also heat the block again while pressurized. You can...
    Post by: derekw, May 13, 2022 in forum: 308/328
  10. derekw
    Post

    My hot rod 308 with NTM wheels

    Are they 17”? Welded”
    Post by: derekw, May 11, 2022 in forum: 308/328
  11. derekw
    Thread

    For Sale 308qv Mondial QV stainless front brake lines

    I found this pair of Goodridge Aeroquip front brake lines while looking through boxes. £100 incl. post in the UK. Post elsewhere at cost. They are...
    Thread by: derekw, May 10, 2022, 0 replies, in forum: Ferrari Parts & Collectibles
  12. derekw
    Post

    83 QV barn find on eBay motors

    Some people spend time instead of money
    Post by: derekw, May 8, 2022 in forum: 308/328
  13. derekw
    Post

    No spark on one bank

    Unplug the VR sensors from the ignition module, check the resistance of each (should be the same) and then turn the engine over and check that...
    Post by: derekw, May 8, 2022 in forum: 308/328
  14. derekw
    Post

    Derek's 308 engine rebuild

    I just sealed the top hats to stop coolant migration into the head gasket-- nothing on the sides or bottom. You are probably fine following the...
    Post by: derekw, May 7, 2022 in forum: 308/328
  15. derekw
    Post

    Rebuilding the 308 electronic ignition (SM805A distributor, Marelli AEI200 Ignition)

    Great tip Andy, too late for us though :-( I heard they are sensitive to EMI so use shielded cable.
    Post by: derekw, May 7, 2022 in forum: 308/328
  16. derekw
    Post

    Derek's 308 engine rebuild

    Joe I don’t think there’s anything controversial about the o-rings, perhaps you mean iron vs aluminium liners? If you have already had yours...
    Post by: derekw, May 5, 2022 in forum: 308/328
  17. derekw
    Post

    308 GTB Brake Calipers

    What prices Mike and Richard?
    Post by: derekw, Apr 30, 2022 in forum: 308/328
  18. derekw
    Post

    Painting my 308

    I got my bodywork (door bottoms changed, patches at the bottom of the rear fenders, unpainted boot/trunk panels replaced, side light holes closed)...
    Post by: derekw, Apr 30, 2022 in forum: 308/328
  19. derekw
    Post

    308 GTB Brake Calipers

    Front are easy to rebuild and kits from biggred. I have a spare new set of stainless lines you can have for £20 less than usual prices (I’m in UK...
    Post by: derekw, Apr 30, 2022 in forum: 308/328
  20. derekw
    Post

    Anybody know where i can get a 368 emblem made?

    Larry, it doesn’t have to be expensive. Keep a look out for a used 348, 355, 360 crank (for increased stroke), bore out or buy bigger bore...
    Post by: derekw, Apr 28, 2022 in forum: 308/328
Showing results 41 to 60 of 195 Next >
Search Again
Page 3 of 10