Search Results | FerrariChat
Buy

Search Results

This site may earn a commission from merchant affiliate links, including eBay, Amazon, Skimlinks, and others.

Search Again
Page 4 of 10
  1. Merdav
    Post

    F355 brake pad sensors

    The Porterfields fit absolutely PERFECT, I have done 2 355's in the past 2 months, they do NOT need to be sanded in any way. Just make sure the...
    Post by: Merdav, Jan 1, 2006 in forum: Technical Q&A
  2. Merdav
    Post

    Help! F355 Brake Warning Light after installing new brake pads

    My Portefields were great for the first 100 or so miles than started squealing also. I changed them out already but same result. Now I grinded a...
    Post by: Merdav, Dec 31, 2005 in forum: Technical Q&A
  3. Merdav
    Post

    F355 brake pad sensors

    Thank you Daniel for going to the trouble, nothing like other people misinforming others about things they say work, that DONT.
    Post by: Merdav, Dec 31, 2005 in forum: Technical Q&A
  4. Merdav
    Post

    355 Dash Leather Re-cover

    Bill what did it cost to replace the dash? p.s. i was going to post a pic of my car but apparently i'm at my attachment limit? Do I have to...
    Post by: Merdav, Dec 28, 2005 in forum: Technical Q&A
  5. Merdav
    Post

    355 Dash Leather Re-cover

    Can you post or email me some pics?
    Post by: Merdav, Dec 28, 2005 in forum: Technical Q&A
  6. Merdav
    Post

    F355 brake pad sensors

    I know the Porterfield R4S do, thats what I used. If you break the sensors your kinda screwed, spray them with WD40 1st and good luck, they are...
    Post by: Merdav, Dec 27, 2005 in forum: Technical Q&A
  7. Merdav
    Post

    F355 Brake Pad Change - What about machining rotors?

    I replaced my 95' 355 pads with the r4s pads a while back. I had plenty of meat still on them but r4s have 90% less dust. I found after properly...
    Post by: Merdav, Dec 24, 2005 in forum: Technical Q&A
  8. Merdav
    Post

    wanting to sell 95 f355b whats it worth

    50K?!?! I'll take two....
    Post by: Merdav, Dec 7, 2005 in forum: 348/355
  9. Merdav
    Post

    355 spider windows opening at high speed

    IF the roof micro switch is turning on you would probably also be hearing some wind noise from the roof as I did, if you loosen the allen screws...
    Post by: Merdav, Dec 2, 2005 in forum: 348/355
  10. Merdav
    Post

    355 front brake pad "wear sensor" missing

    Again....1 front, 1 rear.....
    Post by: Merdav, Nov 23, 2005 in forum: 348/355
  11. Merdav
    Post

    355 front brake pad "wear sensor" missing

    It's not missing, there is one side front and one side rear not all four.
    Post by: Merdav, Nov 23, 2005 in forum: 348/355
  12. Merdav
    Post

    F355 Bypass valve noise

    My question to Wally is this, it's a simply valve that commonly rattles if not adjusted, many of us have tried explaining the way it fuctions to...
    Post by: Merdav, Nov 9, 2005 in forum: Technical Q&A
  13. Merdav
    Post

    F355 Bypass valve noise

    If you tighten the rod you make it shorter and LESS restrictive.
    Post by: Merdav, Nov 7, 2005 in forum: Technical Q&A
  14. Merdav
    Post

    F355 Bypass valve noise

    Your only going to shorten it by a turn or two, it will have almost no effect on the position of it, just enough to take out the slack. Make sure...
    Post by: Merdav, Nov 7, 2005 in forum: Technical Q&A
  15. Merdav
    Post

    355 challenge grill - where to buy?

    Just pulled out my receipt from Ferrari UK, with shipping total price was $633.81, these other guys are rip offs. phone#01784 4362222
    Post by: Merdav, Nov 6, 2005 in forum: 348/355
  16. Merdav
    Post

    F355 Bypass valve noise

    Don't make it longer or you will always have a bad idle spot and it will rattle, make the threaded rod 1 or 2 turns shorter.
    Post by: Merdav, Nov 6, 2005 in forum: Technical Q&A
  17. Merdav
    Post

    F355 Bypass valve noise

    . [ATTACH]
    Post by: Merdav, Nov 6, 2005 in forum: Technical Q&A
  18. Merdav
    Post

    F355 Bypass valve noise

    If it only rattles at idle, pop off the ball fitting, tighten it one or two turns and pop it back on. Or let the dealer do it, $600 ;).
    Post by: Merdav, Nov 5, 2005 in forum: Technical Q&A
  19. Merdav
    Post

    355 challenge grill - where to buy?

    Paid around $700 new for mine.
    Post by: Merdav, Nov 5, 2005 in forum: 348/355
  20. Merdav
    Post

    Question for owner of the black CS w/ black rims in Manhattan

    Actually the owner may frequent this board, just incognito ;).
    Post by: Merdav, Oct 24, 2005 in forum: New York Tri-State
Showing results 61 to 80 of 189 Next >
Search Again
Page 4 of 10