Search Results | FerrariChat
Buy

Search Results

This site may earn a commission from merchant affiliate links, including eBay, Amazon, Skimlinks, and others.

Search Again
Page 2 of 10
  1. Cauf61
    Post

    348 View inside the Climate Control ECU - Info Request

    Also check the diode next to the resistor.
    Post by: Cauf61, Mar 18, 2019 in forum: 348/355
  2. Cauf61
    Post

    What I found on my 348 42k tear down ....

    One thing i did learn is that the lift is positioned wrong on the foto's. The fixed axle of the lift should be at the engine side of the 348. Much...
    Post by: Cauf61, Mar 16, 2019 in forum: 348/355
  3. Cauf61
    Post

    What I found on my 348 42k tear down ....

    This one : https://www.toolmania.nl/nl/tm-volautomatische-poets-hefbrug-elektronisch-30t.html Just be careful when using one !! They are not...
    Post by: Cauf61, Mar 16, 2019 in forum: 348/355
  4. Cauf61
    Post

    What I found on my 348 42k tear down ....

    Me to. It is not perfect but the floor wasn't stable enough to put a 2 post. But be careful for the balance of the 348 on a scissor jack . With...
    Post by: Cauf61, Mar 16, 2019 in forum: 348/355
  5. Cauf61
    Post

    What I found on my 348 42k tear down ....

    Do you mean this ? [ATTACH] [ATTACH]
    Post by: Cauf61, Mar 16, 2019 in forum: 348/355
  6. Cauf61
    Post

    What I found on my 348 42k tear down ....

    Stooge way ;) Very stable. Perfect work height. [ATTACH] [ATTACH]
    Post by: Cauf61, Mar 15, 2019 in forum: 348/355
  7. Cauf61
    Post

    Timing belt noise after major

    I put my tension as advised by the wm. After that is measured the max deflection ( as pictures above from the old belt ) and it was also +- 1.5 cm...
    Post by: Cauf61, Mar 11, 2019 in forum: 348/355
  8. Cauf61
    Post

    Timing belt noise after major

    [MEDIA]
    Post by: Cauf61, Mar 11, 2019 in forum: 348/355
  9. Cauf61
    Post

    Timing belt noise after major

    Good advice on the G string app . LOL Measuring both sides would perhaps give a better result.
    Post by: Cauf61, Mar 11, 2019 in forum: 348/355
  10. Cauf61
    Post

    Timing belt noise after major

    As double check i used "g-string" app ( for tuning guitar strings) and checked for a resonating belt at +- 110-120 hz. This is where i plucked...
    Post by: Cauf61, Mar 10, 2019 in forum: 348/355
  11. Cauf61
    Post

    Timing belt noise after major

    I have done that before removing my old belt. It is in cm !. Hope you can do something with it. I pushed very hard and the belt deflected from...
    Post by: Cauf61, Mar 10, 2019 in forum: 348/355
  12. Cauf61
    Post

    348 Clutch - how long should they last?

    I had to make new flywheel bolts (12.9 steel) also.Some broke during disassembly. [ATTACH] [ATTACH]
    Post by: Cauf61, Mar 7, 2019 in forum: 348/355
  13. Cauf61
    Post

    348 Clutch - how long should they last?

    Now. Was done by a shop in Holland. Top service. [ATTACH] [ATTACH] [ATTACH]
    Post by: Cauf61, Mar 7, 2019 in forum: 348/355
  14. Cauf61
    Post

    348 Clutch - how long should they last?

    My clutch done 58000 km and was end of life. Pressure plate was also not flat any more. The clutch was completely refurbished for 500 euro. New...
    Post by: Cauf61, Mar 7, 2019 in forum: 348/355
  15. Cauf61
    Post

    348 Fuel Pumps - Possible way to free stuck pumps

    Eeeuh , no AC.
    Post by: Cauf61, Feb 20, 2019 in forum: 348/355
  16. Cauf61
    Post

    348 Fuel Pumps - Possible way to free stuck pumps

    Very correct. It is called Inductive Reactance of a coil. When using AC current the coil becomes a resistor.
    Post by: Cauf61, Feb 20, 2019 in forum: 348/355
  17. Cauf61
    Post

    348 348 Parts Thread

    I used an Alfa one like this. Perfect fit.
    Post by: Cauf61, Feb 16, 2019 in forum: 348/355
  18. Cauf61
    Post

    Dash vent flap actuator issue

    Join the club. The things i found on my 348, during DIY major service, not to believe. Silicone everywhere, belts to short, chain tensioner...
    Post by: Cauf61, Feb 9, 2019 in forum: 348/355
  19. Cauf61
    Post

    348 Cam Drive Chain Tensioner.

    Also correct.
    Post by: Cauf61, Feb 8, 2019 in forum: 348/355
  20. Cauf61
    Post

    348 Cam Drive Chain Tensioner.

    I have the drawing if interested. But there is one dimension not correct !!!!! I will look it up. [ATTACH]
    Post by: Cauf61, Feb 8, 2019 in forum: 348/355
Showing results 21 to 40 of 189 Next >
Search Again
Page 2 of 10