Search Results | FerrariChat
Buy

Search Results

This site may earn a commission from merchant affiliate links, including eBay, Amazon, Skimlinks, and others.

Search Again
Page 1 of 2
  1. Robert Johnson
    Post

    Alignment/Suspension Experts Wanted

    I know better than to claim to be an expert at anything. It only invites pissing contests. I can tell you what I know. Increasing caster...
    Post by: Robert Johnson, May 20, 2006 in forum: Technical Q&A
  2. Robert Johnson
    Post

    79 308GTB Chrome Plated nuts??

    The only chrome plated nylock nuts on my '79 308 are the aftermarket ones that were added and the pair in the driver's seat, (painfull but worth it).
    Post by: Robert Johnson, Apr 18, 2004 in forum: Technical Q&A
  3. Robert Johnson
    Post

    328 engine is this a modification

    Most racing bodies require 2 throttle return springs. What you have may have been required by the local autocross club or SCCA. Although, the...
    Post by: Robert Johnson, Mar 10, 2004 in forum: Technical Q&A
  4. Robert Johnson
    Post

    Ben Millermon. Where are you?

    If I had to do it over again, I would not have delt with Ben. Good luck Kermit.
    Post by: Robert Johnson, Feb 28, 2004 in forum: Technical Q&A
  5. Robert Johnson
    Post

    Alternative to Exhaust Donuts on the 308?

    Unless you're going to the car show, the basic design premis for the 308 is this: The engine goes North, South. The exhaust system goes East,...
    Post by: Robert Johnson, Feb 28, 2004 in forum: Technical Q&A
  6. Robert Johnson
    Post

    What's the highest speed you have ever been in your Ferrari?

    My "79 308 GTB, 6700 RPM in 5Th (US Spec speedo only goes to 85) & My 2003 350Z, 147 MPH indicated on the alternate dash pod guage. Both stable...
    Post by: Robert Johnson, Feb 21, 2004 in forum: Ferrari Discussion (not model specific)
  7. Robert Johnson
    Post

    Distributor plate covers for US spec 2v carb engine?

    For what it's worth, my "79 had plugs in the camsfrom the factory and I got a cover from Norwood. I suggest you pull one dizzy and put something...
    Post by: Robert Johnson, Jan 24, 2004 in forum: Technical Q&A
  8. Robert Johnson
    Post

    Have you seen this poster lately?

    Any one have a copy suitable for framing that they want to part with? What are they worth?
    Post by: Robert Johnson, Dec 23, 2003 in forum: Collectables, Literature, & Models
  9. Robert Johnson
    Thread

    Have you seen this poster lately?

    I'm looking for an old poster that I remember seeing in the late 70's through the 80's. I think it was a 308 GTS, a lovely lady (horizontal), and...
    Thread by: Robert Johnson, Dec 22, 2003, 13 replies, in forum: Collectables, Literature, & Models
  10. Robert Johnson
    Post

    cam timing sprokets

    Verell, I contacted Ed Gault regarding his pulley set up just the other day. He e-mailed me back that the timing pulley program had ended and...
    Post by: Robert Johnson, Dec 18, 2003 in forum: Technical Q&A
  11. Robert Johnson
    Post

    Flood Cars

    Buying a flood car is like buying a used condom. It may or may not work, it's cheep, but who wants it?
    Post by: Robert Johnson, Dec 17, 2003 in forum: Technical Q&A
  12. Robert Johnson
    Post

    308 distributor internals

    I went through this with my carb 308. The P.O. had cut the two longer springs and the curve was all off. The two distrobutors were not even...
    Post by: Robert Johnson, Dec 17, 2003 in forum: Technical Q&A
  13. Robert Johnson
    Post

    Perplexed Adjusting Timing On Single Point 308

    Steve King - Check your post. Is 6-7* ATDC correct or should it be BTDC?
    Post by: Robert Johnson, Dec 11, 2003 in forum: Technical Q&A
  14. Robert Johnson
    Post

    So now the engine's comming out.

    yelcab - That's the one. ricrain - You're 100% right. In my case the gasket was leaking before I started. I just did'nt expect to have to...
    Post by: Robert Johnson, Dec 11, 2003 in forum: Technical Q&A
  15. Robert Johnson
    Thread

    So now the engine's comming out.

    Time to change the clutch. OK no big deal. The gasket on the case cover behind the flywheel is leaking some gear oil too. The parts guy I deal...
    Thread by: Robert Johnson, Dec 10, 2003, 3 replies, in forum: Technical Q&A
  16. Robert Johnson
    Post

    My 308

    Great Pic! Lean back and enjoy!
    Post by: Robert Johnson, Nov 9, 2003 in forum: Detailing & Showroom
  17. Robert Johnson
    Post

    Professional 308 carb rebuild -- Weber DCNF 40s

    No black science here, just get the manual and do it.
    Post by: Robert Johnson, Nov 9, 2003 in forum: Technical Q&A
  18. Robert Johnson
    Post

    Average Income of new Ferrari owner

    Dear Mr. Green, I have looked into your post history and can justify asking you to pack sand because it looks as though the world is all about...
    Post by: Robert Johnson, Nov 8, 2003 in forum: Ferrari Discussion (not model specific)
  19. Robert Johnson
    Post

    Time for a clutch

    Thanks for all of your kind responses. As a matter or protocall, England is England. The UK is England, Scotland, Whalels and Northern Iserland....
    Post by: Robert Johnson, Nov 8, 2003 in forum: Technical Q&A
  20. Robert Johnson
    Post

    Clunking rear suspension on 308?

    My car does the same thing, I have new shocks and urethane suspention bushings. Turns out the problem is in the rear hatch closers. The right...
    Post by: Robert Johnson, Nov 8, 2003 in forum: Technical Q&A
Showing results 1 to 20 of 22 Next >
Search Again
Page 1 of 2