Search Results | FerrariChat

Search Results

This site may earn a commission from merchant affiliate links, including eBay, Amazon, Skimlinks, and others.

Search Again
Page 1 of 9
  1. Nielsk
    Post

    2V valves group buy (non-sodium!!)

    I had sent a PM a while back hoping to get in on this, any chance? Thanks!
    Post by: Nielsk, Nov 8, 2016 in forum: 308/328
  2. Nielsk
    Post

    Derek's 308 engine rebuild

    I still miss my GT6MkIII I could change a fan belt on the side of the road and be back driving in under 5 minutes... and sit comfortably on the...
    Post by: Nielsk, Oct 25, 2016 in forum: 308/328
  3. Nielsk
    Post

    Sodium Valves

    VMAXIM, did you get the guides and seals from SI valves as well?
    Post by: Nielsk, Jan 6, 2016 in forum: 308/328
  4. Nielsk
    Post

    GT4 SUSPENSION FORK WONT BUDGE

    S/F = superformance How can you determine it has not been apart since it was built? The fact that the fork bolt was installed the wrong way round...
    Post by: Nielsk, Jul 4, 2015 in forum: 308/328
  5. Nielsk
    Post

    Anyone bidding on this GT4?

    Josef Mengele ll Duce joint venture? Rip it all off and make a race car..
    Post by: Nielsk, Jul 4, 2015 in forum: 308/328
  6. Nielsk
    Post

    GT4 SUSPENSION FORK WONT BUDGE

    S/F has the tiny pins (100796) and yes, you need all four on each side, despite what the last mechanic did. They also carry the rubber seals...
    Post by: Nielsk, Jul 4, 2015 in forum: 308/328
  7. Nielsk
    Post

    Robs New Ferrari 308 GT4 Adventure

    Get 'em to install the sniffer pipes on the headers...
    Post by: Nielsk, Jun 8, 2015 in forum: 308/328
  8. Nielsk
    Post

    GT4 stuck gear oil fill plugs...

    Be very careful about using that propane torch in the greasy engine bay! A heat gun is much safer, no open flame, and more dispersed heat...
    Post by: Nielsk, Apr 16, 2015 in forum: 308/328
  9. Nielsk
    Post

    GT4 stuck gear oil fill plugs...

    There is always heating the area right around it up with a heat gun, then icing the plug to shrink it. Sometimes tightening it just a bit helps...
    Post by: Nielsk, Apr 15, 2015 in forum: 308/328
  10. Nielsk
    Thread

    Did you upgrade rear sway bar? I need one old dished washer...!

    Of course, yet another bit some mechanic that is currently roasting over a pit of flames left off my car, I am in need of one of the dished...
    Thread by: Nielsk, Mar 2, 2015, 4 replies, in forum: 308/328
  11. Nielsk
    Post

    308 GT4 resurection

    Those headers look great! Did they not have the mixture sniffing ports? Now is the time to install the tubes if you have the ports... Did you...
    Post by: Nielsk, Feb 26, 2015 in forum: 308/328
  12. Nielsk
    Post

    308 GT4 resurection

    Do you know what the Centrex website is? Nothing on google, not for Centrix either...
    Post by: Nielsk, Feb 20, 2015 in forum: 308/328
  13. Nielsk
    Post

    308 GT4 resurection

    What was the cost for the rebuild by Centrix? how difficult do you think removing the front header would be without a lift (on jack-stands)......
    Post by: Nielsk, Feb 19, 2015 in forum: 308/328
  14. Nielsk
    Post

    Does this look right?

    Interesting, some consensus... they are the correct shocks, this is a GT4. The front apparently requires the different stem length to clear the a...
    Post by: Nielsk, Jan 21, 2015 in forum: 308/328
  15. Nielsk
    Post

    Does this look right?

    Thanks for your reply, it looks like your pic is of a rear shock, this is on the front only. I have found no reference to these spacers in the GT4...
    Post by: Nielsk, Jan 21, 2015 in forum: 308/328
  16. Nielsk
    Thread

    Does this look right?

    Finally everything is ready to go back together on the 308 GT4 full suspension rebuild, all clean, powder coated, new parts ready and waiting......
    Thread by: Nielsk, Jan 20, 2015, 16 replies, in forum: 308/328
  17. Nielsk
    Post

    GT4 wiper arm needed

    eurospares can be a good source for salvage parts, no aff. but I'm a happy customer so far
    Post by: Nielsk, Dec 4, 2014 in forum: 308/328
  18. Nielsk
    Post

    Forza article on Robert Garven

    Very nice article and well deserved. I hope they fix the typo on line #1 of paragraph #3 before it goes to print... and include more photos, a joy...
    Post by: Nielsk, Dec 4, 2014 in forum: 308/328
  19. Nielsk
    Post

    Rebuilding front shocks. What oil should I use?

    O ring is 2" O. D., 0.125" thick
    Post by: Nielsk, Oct 10, 2014 in forum: 308/328
  20. Nielsk
    Post

    Hockey Pucks?

    a 1' x 1' or so square of 3/4" plywood works a charm
    Post by: Nielsk, Oct 1, 2014 in forum: 308/328
Showing results 1 to 20 of 179 Next >
Search Again
Page 1 of 9