Search Results | FerrariChat

Search Results

This site may earn a commission from merchant affiliate links, including eBay, Amazon, Skimlinks, and others.

Search Again
Page 1 of 6
  1. Dorsetgem
    Post

    Torque wrench

    Warren and Brown Deflecting Beam , not cheap but very accurate.
    Post by: Dorsetgem, Aug 3, 2023 in forum: 308/328
  2. Dorsetgem
    Post

    Another 308 with issues starting

    I had an issue when I first had my QV where the engine would turn over fine but not start. It would bump fine so after checking everything...
    Post by: Dorsetgem, Feb 4, 2023 in forum: 308/328
  3. Dorsetgem
    Post

    308 gts identification

    Looks like they finally sold the converted car, I hope the purchaser realised that it wasn't originally a RHD car as the advert could be read as...
    Post by: Dorsetgem, Dec 11, 2022 in forum: 308/328
  4. Dorsetgem
    Post

    Spark plug wire set options

    That's what I did last year, total cost around £60 and 3-4 hours to change.
    Post by: Dorsetgem, Sep 15, 2022 in forum: 308/328
  5. Dorsetgem
    Post

    Help the Dummy, Please, Wiring Question

    I would purchase the bare plug with new pins and purchase the correct crimp tool and install without any joints, it would then look factory and be...
    Post by: Dorsetgem, Sep 15, 2022 in forum: 308/328
  6. Dorsetgem
    Thread

    Warning on this car for sale in the UK

    There is a seller on PistonHeads selling a 308 stating that its a genuine Right Hand Drive. I have emailed the seller (a business) to let him know...
    Thread by: Dorsetgem, Feb 26, 2022, 3 replies, in forum: 308/328
  7. Dorsetgem
    Post

    Ignition Fault

    Update as to where I am at. Thanks again for everybody's input this is really a valuable knowledge base. I was going through all of what I had...
    Post by: Dorsetgem, Jan 30, 2021 in forum: 308/328
  8. Dorsetgem
    Post

    Ignition Fault

    Thanks Steve, curious thing, went in to the garage this afternoon and tested at the digiplexes for the TDC sensor which runs both Digiplexes and...
    Post by: Dorsetgem, Jan 15, 2021 in forum: 308/328
  9. Dorsetgem
    Post

    Ignition Fault

    Well today I installed the Digiplexes, bridged out the alarm and again no start. So plugged alarm back in again and noticed that I had forgotten...
    Post by: Dorsetgem, Jan 10, 2021 in forum: 308/328
  10. Dorsetgem
    Post

    Ignition Fault

    Well back to the drawing board as the ECU's were sent off to the ECU Doctor and came back with no fault found ?. So with working TDC sensors,...
    Post by: Dorsetgem, Jan 9, 2021 in forum: 308/328
  11. Dorsetgem
    Post

    Ignition Fault

    Here are the images of the coils signal. [ATTACH] [ATTACH]
    Post by: Dorsetgem, Jan 1, 2021 in forum: 308/328
  12. Dorsetgem
    Post

    Ignition Fault

    Ok so I have taken more readings with both the scope and multimeter. I took the readings from Pin 1 of each coil and chassis ground. Coil bank 5-8...
    Post by: Dorsetgem, Dec 31, 2020 in forum: 308/328
  13. Dorsetgem
    Post

    Ignition Fault

    Thanks Gents for the explanation, I will have another go tomorrow.
    Post by: Dorsetgem, Dec 30, 2020 in forum: 308/328
  14. Dorsetgem
    Post

    Ignition Fault

    Thanks again Steve I thought John had connected his scope from Pin 1 & Pin 15 in post #5. Pin 1 coming from the Digiplex and Pin 15 from ignition...
    Post by: Dorsetgem, Dec 30, 2020 in forum: 308/328
  15. Dorsetgem
    Post

    Ignition Fault

    Ok I have completed my testing and here are the results Crank Sensor Banks 1-4 TDC 665 Ohms 5-8 TDC...
    Post by: Dorsetgem, Dec 30, 2020 in forum: 308/328
  16. Dorsetgem
    Post

    Compomotive split rim advice

    I have the same set, albeit with different centres.I am planning to have them restored as, well as I have managed to find at set of Ferrari...
    Post by: Dorsetgem, Dec 30, 2020 in forum: 308/328
  17. Dorsetgem
    Post

    Ignition Fault

    Once again thank you, will have another look tomorrow & let you know how I get on. I really appreciate your time and knowledge. Glen
    Post by: Dorsetgem, Dec 28, 2020 in forum: 308/328
  18. Dorsetgem
    Post

    Ignition Fault

    I saw him pull a HT lead from one of the coils & connect a longer HT lead into a coil and then he asked me to crank the engine. I think he held...
    Post by: Dorsetgem, Dec 28, 2020 in forum: 308/328
  19. Dorsetgem
    Post

    Ignition Fault

    Thanks again Steve. Do you know how easy it is to damage these Digiplexes ?
    Post by: Dorsetgem, Dec 28, 2020 in forum: 308/328
  20. Dorsetgem
    Post

    Ignition Fault

    Thanks John. After testing the at the Digipexes yesterday I found one dead sensor (bank 1-4) but I am confused about the signal from the Bank 5-8...
    Post by: Dorsetgem, Dec 28, 2020 in forum: 308/328
Showing results 1 to 20 of 115 Next >
Search Again
Page 1 of 6