Search Results | FerrariChat
Buy

Search Results

This site may earn a commission from merchant affiliate links, including eBay, Amazon, Skimlinks, and others.

Search Again
Page 1 of 2
  1. Ferdinand Mayr
    Post

    365 GTB/4 Daytona Windshield Wiper Setup

    Thank you all for your input!
    Post by: Ferdinand Mayr, Sep 17, 2022 in forum: Technical Q&A
  2. Ferdinand Mayr
    Thread

    365 GTB/4 Daytona Windshield Wiper Setup

    Hi Everyone, the windshield wipers on my Daytona are not properly setup. When turned on the blades go beyond either side of the window barely...
    Thread by: Ferdinand Mayr, Sep 16, 2022, 4 replies, in forum: Technical Q&A
  3. Ferdinand Mayr
    Thread

    246 Dino GT Fuel, Oil Temp, Water Temp and Rec Counter down

    Problem solved
    Thread by: Ferdinand Mayr, Jul 30, 2022, 0 replies, in forum: Technical Q&A
  4. Ferdinand Mayr
    Thread

    My Daytona almost burned down

    Hi everyone, I almost lost my Daytona today to - what most definitely seems to have been - a cable fire. Most likely originating from the...
    Thread by: Ferdinand Mayr, Jul 28, 2021, 14 replies, in forum: Technical Q&A
  5. Ferdinand Mayr
    Post

    365 GTB/4 Daytona break warning lamp („FRENO“)

    Thanks Jimmy. What exactly did you have to fix in your master cylinder?
    Post by: Ferdinand Mayr, Jun 21, 2021 in forum: Technical Q&A
  6. Ferdinand Mayr
    Post

    365 GTB/4 Daytona break warning lamp („FRENO“)

    Thanks for your reply. However it can‘t be an imbalance between front and rear breaks, because each break-circuit works for all 4 wheels (see...
    Post by: Ferdinand Mayr, Jun 21, 2021 in forum: Technical Q&A
  7. Ferdinand Mayr
    Thread

    365 GTB/4 Daytona break warning lamp („FRENO“)

    Hi everyone, my Daytona‘s „FRENO“ lamp is lighting up whenever I perform a hard breaking. The light remains off when I just break „normally“....
    Thread by: Ferdinand Mayr, Jun 20, 2021, 8 replies, in forum: Technical Q&A
  8. Ferdinand Mayr
    Thread

    365 GTB/4 Daytona Exhaust Replacement

    Hi everyone, my Daytona‘s exhaust needs to be replaced due to various holes caused by rust. I‘ve found a manufacturer from the UK who produces...
    Thread by: Ferdinand Mayr, Apr 13, 2021, 4 replies, in forum: Technical Q&A
  9. Ferdinand Mayr
    Post

    How to keep vent window from closing at higher speeds

    Thanks for your reply Peter. Unfortunately my power drill was quicker than your answer :)...But it worked like a charm: I can now reach through...
    Post by: Ferdinand Mayr, Oct 11, 2020 in forum: 206/246
  10. Ferdinand Mayr
    Post

    How to keep vent window from closing at higher speeds

    Thanks! If it‘s the clamp then my worst fears have come true...It‘s impossible to reach the clamp screw without removing the entire frame out of...
    Post by: Ferdinand Mayr, Oct 11, 2020 in forum: 206/246
  11. Ferdinand Mayr
    Thread

    How to keep vent window from closing at higher speeds

    Does anyone have a solution for keeping the vent windows of the Dino from closing due to wind at higher speeds? The vent windows will not remain...
    Thread by: Ferdinand Mayr, Oct 10, 2020, 19 replies, in forum: 206/246
  12. Ferdinand Mayr
    Post

    365 GTB/4 Daytona gasket for fuel supply into carburators

    Thanks a lot for the info!
    Post by: Ferdinand Mayr, Oct 3, 2020 in forum: Technical Q&A
  13. Ferdinand Mayr
    Thread

    365 GTB/4 Daytona gasket for fuel supply into carburators

    Hi everyone, two of my gaskets that connect the fuel supply to the carburators on my Daytona are not 100% sealing anymore. When the engine is...
    Thread by: Ferdinand Mayr, Oct 3, 2020, 3 replies, in forum: Technical Q&A
  14. Ferdinand Mayr
    Post

    Knocking noise Dino 246 GT

    Thanks a lot for your message! I already bought it.
    Post by: Ferdinand Mayr, Jul 23, 2020 in forum: 206/246
  15. Ferdinand Mayr
    Post

    Knocking noise Dino 246 GT

    Hi everyone, I found these replacement bearings from SKF: https://www.sparepartstore24.co.uk/19128-skf Can anyone tell me if they will...
    Post by: Ferdinand Mayr, Jul 6, 2020 in forum: 206/246
  16. Ferdinand Mayr
    Post

    Knocking noise Dino 246 GT

    Thanks to everyone for your help!! I just made a quick „inspection drive“. I was able to narrow the noise down even more: The knocking sound is...
    Post by: Ferdinand Mayr, Jul 4, 2020 in forum: 206/246
  17. Ferdinand Mayr
    Post

    Knocking noise Dino 246 GT

    here‘s the video: https://www.dropbox.com/s/ve8u3m1vdb19nbr/VIDEO-2020-07-04-10-27-41.mp4?dl=0
    Post by: Ferdinand Mayr, Jul 4, 2020 in forum: 206/246
  18. Ferdinand Mayr
    Post

    Knocking noise Dino 246 GT

    Heres a video of the CV joint. When I move the left one there is a knocking noise. The right one does not make a noise. I think this could be it!
    Post by: Ferdinand Mayr, Jul 4, 2020 in forum: 206/246
  19. Ferdinand Mayr
    Post

    Knocking noise Dino 246 GT

    Thanks for your help Peter! Do you think it‘s an issue I should immediately take care of or will it be fine if I wait until the season is over in...
    Post by: Ferdinand Mayr, Jul 4, 2020 in forum: 206/246
  20. Ferdinand Mayr
    Post

    Knocking noise Dino 246 GT

    Thanks, but as I said the noise only appears when the car is in a gear. Once I press the clutch it‘s gone. So wheels, tires, suspension are...
    Post by: Ferdinand Mayr, Jul 4, 2020 in forum: 206/246
Showing results 1 to 20 of 22 Next >
Search Again
Page 1 of 2