Search Results | FerrariChat

Search Results

This site may earn a commission from merchant affiliate links, including eBay, Amazon, Skimlinks, and others.

Search Again
Page 1 of 2
  1. Emanuele
    Post

    599 Repair Manual

    Thank you very much!
    Post by: Emanuele, Sep 8, 2023 in forum: 612/599
  2. Emanuele
    Post

    599 Repair Manual

    Hi George, I'am also interested in the 599 manual can you send me at : [email protected] Many thanks !
    Post by: Emanuele, Sep 6, 2023 in forum: 612/599
  3. Emanuele
    Post

    Ferrari 348 tb cambelt service

    Did you find water into the cylinders?
    Post by: Emanuele, Oct 5, 2011 in forum: 348/355
  4. Emanuele
    Post

    Exhaust ECU aka SDECU

    You may use a 4.7V zener diode and a resistor.
    Post by: Emanuele, Oct 1, 2011 in forum: Technical Q&A
  5. Emanuele
    Post

    Ferrari 348 tb cambelt service

    Take a look at this: http://www.youtube.com/watch?v=F4uSn-0Qfjg at 7:14 they say that they apply some RTV ( CAF4 I think ) to avoid leaks. Since...
    Post by: Emanuele, Sep 29, 2011 in forum: 348/355
  6. Emanuele
    Post

    Check Engine Light On

    The car has 30000 Km.
    Post by: Emanuele, May 16, 2011 in forum: 456/550/575
  7. Emanuele
    Post

    Check Engine Light On

    I had to replace the worn bronze guides on 550 and now I'm in trouble with the head gaskets. Take a look to...
    Post by: Emanuele, May 15, 2011 in forum: 456/550/575
  8. Emanuele
    Post

    Leaking head gasket after assembly on 550 Maranello

    The old gasket, has no signs of sealant, I'm curious to know how the gaskets are mounted by the Factory. Maybe they use a different procedure....
    Post by: Emanuele, May 11, 2011 in forum: Technical Q&A
  9. Emanuele
    Post

    Leaking head gasket after assembly on 550 Maranello

    I've just removed the gasket, it looks like new. Even the rubber stripes are not compressed and this is very strange. I also removed the studs,...
    Post by: Emanuele, May 10, 2011 in forum: Technical Q&A
  10. Emanuele
    Post

    Leaking head gasket after assembly on 550 Maranello

    Interesting Dave, so are you going to sell head gaskets for the 550? By the way anyone knows if the studs are torque to yield? I kown they are...
    Post by: Emanuele, May 7, 2011 in forum: Technical Q&A
  11. Emanuele
    Post

    Leaking head gasket after assembly on 550 Maranello

    The head stud nuts are open on both ends. The car has 30000 Km.
    Post by: Emanuele, May 7, 2011 in forum: Technical Q&A
  12. Emanuele
    Post

    Leaking head gasket after assembly on 550 Maranello

    Josh, I did a leak down test and the values are correct (and way better than before the valve job). The value in the cylinder where I found the...
    Post by: Emanuele, May 6, 2011 in forum: Technical Q&A
  13. Emanuele
    Post

    Leaking head gasket after assembly on 550 Maranello

    Thank you Alfredo, the procedure is: Pre torque all the nuts to 60Nm in the order shown and then tighten by furter 90°. [ATTACH]
    Post by: Emanuele, May 6, 2011 in forum: Technical Q&A
  14. Emanuele
    Thread

    Leaking head gasket after assembly on 550 Maranello

    Hi, after a valve job I have torqued the head down using the procedure in the WSM. The heads where refaced, I didn't replace the studs. Then I...
    Thread by: Emanuele, May 6, 2011, 47 replies, in forum: Technical Q&A
  15. Emanuele
    Post

    355 head tool

    This is a pic taken from the Hill Engineering tool. HTH Emanuele [ATTACH]
    Post by: Emanuele, Sep 15, 2010 in forum: 348/355
  16. Emanuele
    Thread

    550 and 575 TSB

    Hi, Does anyone knows where to find all the 550 and 575 TSB's? Thanks in advance Emanuele
    Thread by: Emanuele, May 19, 2010, 11 replies, in forum: 456/550/575
  17. Emanuele
    Post

    Need 550 timing information

    Hi, I'll try to answer: 1) 216 Nm (page B 70 on WSM - Damper fastening to crankshaft) 2) 56 Nm 3) The tensioner bearing bolt should be loose,...
    Post by: Emanuele, Apr 12, 2010 in forum: Technical Q&A
  18. Emanuele
    Post

    Wondering if anyone has an ecu pinout diagram for 99 550

    I know it's not exactly what you need but hope this helps (it is in italian). [ATTACH]
    Post by: Emanuele, Dec 15, 2009 in forum: Technical Q&A
  19. Emanuele
    Post

    Magneti Marelli voltage regulator

    Since it has a glass case, it looks like a germanium diode. It may be a AA118 - AA119 - OA95.
    Post by: Emanuele, Dec 1, 2009 in forum: Technical Q&A
  20. Emanuele
    Post

    Motronic ECU died

    Thanks for the reply Speedmore. Here some "macro" pics. Forgive the poor quality. As far as I can see there are no short circuits between PCB and...
    Post by: Emanuele, Oct 28, 2009 in forum: Technical Q&A
Showing results 1 to 20 of 33 Next >
Search Again
Page 1 of 2