308 Question about gear trans pan bearing and springs | FerrariChat
Buy

308 Question about gear trans pan bearing and springs

Discussion in 'Technical Q&A' started by f68, Feb 2, 2014.

This site may earn a commission from merchant affiliate links, including eBay, Amazon, Skimlinks, and others.

  1. f68

    f68 Karting

    Jan 4, 2014
    75
    Orange Co California
    Full Name:
    Rodz Of Ages
    #1 f68, Feb 2, 2014
    Last edited by a moderator: Sep 7, 2017
    I am replacing my shift shaft seal and all my fluids in my 1982 308 GTSI first I removed the oil pan then I removed very gently the gear Trans pan so I wouldn’t lose any ball bearings or springs. Well my question is there supposed to be three bearings see pic below Fig2 bearing missing?
    Thanks
    Image Unavailable, Please Login
     
  2. smg2

    smg2 F1 World Champ
    Sponsor

    Apr 1, 2004
    16,329
    Dumpster Fire #31
    Full Name:
    SMG
    #2 smg2, Feb 2, 2014
    Yes, 3 ball bearings, one for each spring. It may still be in the shaft, held by the grease. a small magnetic would retrieve it, if still there, otherwise it's fallen out and rolled away. Possibly the last time someone pulled the pan.
     
  3. f68

    f68 Karting

    Jan 4, 2014
    75
    Orange Co California
    Full Name:
    Rodz Of Ages
    #3 f68, Feb 2, 2014
    Thanks for the info smg2 i will check tomorrow with a magnet to see if that little bugger still in there. Do i need to replace it if missing?

    And what would be the Torque Specs for the pan nuts
     
  4. Iain

    Iain F1 Rookie

    Jan 21, 2005
    3,320
    UK
    #4 Iain, Feb 2, 2014
    You definitely need to replace it if its MIA.

    Top tip for replacing these is to use a blob of grease in each hole - it will be enough to hold the balls & springs in place while you put the pan back on. Torque for the pan nuts is the std 6.5 lbft / 10NM
     
  5. f68

    f68 Karting

    Jan 4, 2014
    75
    Orange Co California
    Full Name:
    Rodz Of Ages
    #5 f68, Feb 2, 2014
    Thanks Iain if the bearing is MIA can you guys point me in the right direction on who sales them. And what would the name of these little bearings be
    Thanks for the help guys
     
  6. Iain

    Iain F1 Rookie

    Jan 21, 2005
    3,320
    UK
    #6 Iain, Feb 2, 2014
    Believe the spring is part #100750 & the ball bearing is #101612

    Daniel at Ricambi should be able to help

    Ferrari 328 (1985) Parts : Table 28 - INSIDE GEARBOX CONTROLS

    Parts 16/17/18 . Good job you've got the spring by the look of the price, though I don't know why it should be so expensive (maybe a misprint?).

    Its less than $2 at ferrariparts.co.uk (which is the main global distribution point)
     
  7. f68

    f68 Karting

    Jan 4, 2014
    75
    Orange Co California
    Full Name:
    Rodz Of Ages
    #7 f68, Feb 2, 2014
    nice thanks Iain
     
  8. Iain

    Iain F1 Rookie

    Jan 21, 2005
    3,320
    UK
    #8 Iain, Feb 2, 2014
    That parts diag. is for a 328 but pretty sure the part is common
     
  9. f68

    f68 Karting

    Jan 4, 2014
    75
    Orange Co California
    Full Name:
    Rodz Of Ages
    #9 f68, Feb 2, 2014
    i will call them tomarrow
    thanks for your time
     
  10. 2NA

    2NA F1 World Champ
    Consultant Owner Professional Ferrari Technician

    Dec 29, 2006
    18,221
    Twin Cities
    Full Name:
    Tim Keseluk
    #10 2NA, Feb 2, 2014
    If it's just the ball that's missing you might get lucky at the hardware store. Bring one of the others along to compare. Probably less than a buck.
     
  11. smg2

    smg2 F1 World Champ
    Sponsor

    Apr 1, 2004
    16,329
    Dumpster Fire #31
    Full Name:
    SMG
    #11 smg2, Feb 2, 2014
    mcmaster-carr, I think they're 8mm so that'd be 9292k45 ~$3 for 25.
     
  12. f68

    f68 Karting

    Jan 4, 2014
    75
    Orange Co California
    Full Name:
    Rodz Of Ages
    #12 f68, Feb 3, 2014
    I got lucky and i found that littlel bearing
    Thanks for all the help.
     

Share This Page