308 QV front bonnet swap to carb car | FerrariChat
Buy

308 QV front bonnet swap to carb car

Discussion in 'Technical Q&A' started by cavallo_nero, Apr 15, 2005.

This site may earn a commission from merchant affiliate links, including eBay, Amazon, Skimlinks, and others.

  1. cavallo_nero

    cavallo_nero Formula 3

    Nov 3, 2003
    1,707
    colorado
    Full Name:
    Giovanni Pasquale
    #1 cavallo_nero, Apr 15, 2005
    I recently purchaced a brand new 308 QV front bonnet for my carb 308 (1978 euro) from Ferrari UK. The body shop has informed me that the hinge mounts on the hood do not line up. I was told that the hood swap would work however. Has anyone run into this, or have any information to contribute. I will see if I can send thehood back to Ferrari UK, but will most likely eat the shipping. Anyone interested in buying a new QV front bonnet for a 308 QV??
     
  2. Artvonne

    Artvonne F1 Veteran

    Oct 29, 2004
    5,379
    NWA
    Full Name:
    Paul
    #2 Artvonne, Apr 15, 2005


    How much?
     
  3. Jdubbya

    Jdubbya The $10 Trillion Man
    Silver Subscribed

    Dec 28, 2003
    43,674
    Hell's waiting room
    Full Name:
    John
    #3 Jdubbya, Apr 16, 2005
    They can't make it work at all? Not sure what the structure of a QV hood looks like but on the '78 it's just basically a "tapping block" that's welded onto the tubing. Seems like unless the interior structure is completely different it should be pretty simple to fab up a new "block".
     
  4. thecarreaper

    thecarreaper F1 World Champ
    Silver Subscribed

    Sep 30, 2003
    18,130
    Savannah
    #4 thecarreaper, Apr 16, 2005
    i fixed the marrone 308 ( front damage) with hand tools and a frame machine by myself. find another bodyshop.
     
  5. 208 GT4

    208 GT4 Formula 3

    Dec 27, 2003
    1,769
    Brighton (UK)
    Full Name:
    Dan
    #5 208 GT4, Apr 16, 2005
    How much is it out by? The cars were hand finished, so if it's out by a small amount (a few mm) that's normal and a replacement might not be any better.
     
  6. matteo

    matteo F1 World Champ

    Aug 1, 2002
    13,748
    On a plane somewhere
    Full Name:
    Heir Butt
    #6 matteo, Apr 16, 2005
    Agreed
     
  7. bernardo66

    bernardo66 The Crazy Cat Man
    Lifetime Rossa Owner

    Dec 14, 2003
    26,591
    Montreal Canada
    Full Name:
    Bernie
    #7 bernardo66, Apr 16, 2005
    I second that. Any shop that has an ounce of creativity will be able to fix ANY problem.
     
  8. cavallo_nero

    cavallo_nero Formula 3

    Nov 3, 2003
    1,707
    colorado
    Full Name:
    Giovanni Pasquale
    #8 cavallo_nero, Apr 17, 2005
    heres more info. the hinge holes are a good half inch off, my question was if this is normal - like did i get a bugus hood. i want to be able to disclose this when selling the hood. the body shop i am dealing is an incredible shop and can do anything with surgical precision (they have completely chemical stripped my 308 and flexed each hail dent by hand, covered up side marker light holes and are building a rear wheel duct like on the 250gto). the cost of moving hinge points was a wash with repairing the old hood (hail dents) and cutting a section out for the QV vent which is what i want. plus there were parts on the qv hood (landing tabs/posts??) that needed to be cut off cause the carb hood did not have those either (in the underside of hood). the hood cost me $460 plus a whopping $340 in shipping. apparently it is NOS. i will sell it for $450 plus shiping - i estimate shipping at about $90. but again, my question is,,are there known differences in the hinge mounting points to the front bonnet on these suckas between QV and carb??....
    thanks.........john
     
  9. cavallo_nero

    cavallo_nero Formula 3

    Nov 3, 2003
    1,707
    colorado
    Full Name:
    Giovanni Pasquale
    #9 cavallo_nero, Apr 17, 2005
    i just realized i did not get my burning question across too well in my initial post - my bad........
     
  10. Dr Tommy Cosgrove

    Dr Tommy Cosgrove Three Time F1 World Champ
    Owner Rossa Subscribed

    May 4, 2001
    36,599
    Birmingham, AL
    Full Name:
    Tommy
    #10 Dr Tommy Cosgrove, Apr 17, 2005
    I ran into ths same problem but in reverse. I was fitting a carb hood on my 308 QV. Things didn't line up too well for us either. Right now the hood is at the body shop waiting for me to bring the car back. I'll let everyone know how we figured it out when we get it on.
     
  11. branko

    branko F1 Rookie
    Owner

    Mar 17, 2003
    3,710
    Birmingham, Alabama
    Full Name:
    Branko Medenica
    #11 branko, Apr 17, 2005
    Tommy, why don't you and John just swap hoods?
     
  12. Dr Tommy Cosgrove

    Dr Tommy Cosgrove Three Time F1 World Champ
    Owner Rossa Subscribed

    May 4, 2001
    36,599
    Birmingham, AL
    Full Name:
    Tommy
    #12 Dr Tommy Cosgrove, Apr 17, 2005
    I want to keep both of mine
     
  13. cavallo_nero

    cavallo_nero Formula 3

    Nov 3, 2003
    1,707
    colorado
    Full Name:
    Giovanni Pasquale
    #13 cavallo_nero, Apr 18, 2005
    well, Tommy, that is interesting. is it the hinge mounting points in your hood that do not line up???? now i am feeling a bit better about the QV hood i bought - seems like there is a difference and the QV hood i got will fit a qV but not a carb car. let me know what you find out - OK??? thanks
    john
    too late to swap out hoods for me, they already started cutting into my carb hood to fit the vent.......
     
  14. Dr Tommy Cosgrove

    Dr Tommy Cosgrove Three Time F1 World Champ
    Owner Rossa Subscribed

    May 4, 2001
    36,599
    Birmingham, AL
    Full Name:
    Tommy
    #14 Dr Tommy Cosgrove, Apr 18, 2005
    I really do not remember the exact details. My next door neighbor is doing it and neither of us is in a hurry. I do remember it wasn't easy. I'll ask him tonight and let you know.
     

Share This Page