308 Steering Wheel Ring Nut Tool - Anyone have one? | FerrariChat
Buy

308 Steering Wheel Ring Nut Tool - Anyone have one?

Discussion in '308/328' started by johnb@macarbon, Oct 13, 2008.

This site may earn a commission from merchant affiliate links, including eBay, Amazon, Skimlinks, and others.

  1. johnb@macarbon

    johnb@macarbon Formula Junior

    Feb 24, 2004
    809
    SF Bay Area
    Full Name:
    John Borchelt
    #1 johnb@macarbon, Oct 13, 2008
    Last edited by a moderator: Sep 7, 2017
    I need to take the steering wheel off my '83 308QV in order to send the turn signal mechanism to Verell for rebuilding. You need a 'Ring Nut' tool to remove the ring nut that holds on the wheel. (Why did Ferrari not use a standard nut?) Ricambi sells them but its a little painful to buy one for this project and never use it again. Hopefully!

    Anyone have one and MOST IMPORTANT want to sell it or rent it out? Please PM me. Thanks!
    Image Unavailable, Please Login
    Image Unavailable, Please Login
     
  2. pad

    pad Formula 3

    Sep 30, 2004
    1,426
    Tequesta, FL
    Full Name:
    Paul Delatush
    #2 pad, Oct 13, 2008
    Do the search. There are several threads on how to make your own out of a piece of pipe. I made one - total cost under $3.00.
     
  3. jon s

    jon s Formula Junior

    Mar 9, 2005
    509
    pocasset ma
    Full Name:
    jon shoukimas MD
    #3 jon s, Oct 13, 2008
    i notched an old socket to fit with a dremel tool. took 10 minutes and worked fine. i confess though that i removed the shaft nut the first time with a vice grip and used the nut as a guide off the shaft. regards, jon s
     
  4. johnb@macarbon

    johnb@macarbon Formula Junior

    Feb 24, 2004
    809
    SF Bay Area
    Full Name:
    John Borchelt
    #4 johnb@macarbon, Oct 13, 2008
    I saw the old thread Verell includes with his instructions. I'll search for the other instructions but I was hoping not to spend a day chasing it down. If someone has one and wants to 'move it on' let me know.
     
  5. miketuason

    miketuason F1 World Champ
    Owner Silver Subscribed

    Feb 24, 2006
    15,833
    Cerritos, CA.
    Full Name:
    Mike
    #5 miketuason, Oct 13, 2008
    Last edited by a moderator: Sep 7, 2017
    Geez John, where were you when I needed one:)

    Anyway I was force to make one out of a 1 1/4 socket

    and works like a charm but I may still get your tool just in case.
    Image Unavailable, Please Login
     
  6. johnb@macarbon

    johnb@macarbon Formula Junior

    Feb 24, 2004
    809
    SF Bay Area
    Full Name:
    John Borchelt
    #6 johnb@macarbon, Oct 13, 2008
    I just wound up taking a very large pair of needle nose pliers to it. It came off without too much of a problem.
    Nice work on yours Mike!
     
  7. Dr Tommy Cosgrove

    Dr Tommy Cosgrove Three Time F1 World Champ
    Owner Rossa Subscribed

    May 4, 2001
    36,599
    Birmingham, AL
    Full Name:
    Tommy
    #7 Dr Tommy Cosgrove, Oct 13, 2008
    I have it.

    If you promise to send it back I'll mail it to you tomorrow. PM me your address.

    Remember, if I don't get it back I am sending Guido after you...
     
  8. f308jack

    f308jack F1 Rookie

    Jun 7, 2007
    4,300
    Cape Town, South Afr
    Full Name:
    Jack Verschuur
    #8 f308jack, Oct 14, 2008
    All I see is rather expensive single sockets offered. Why isn't anyone making a set of the most common sizes? There must be a market for them. Something to look into?
     

Share This Page