348TS Rear Headliner Upholstery is Falling Off! Help! | FerrariChat
Buy

348TS Rear Headliner Upholstery is Falling Off! Help!

Discussion in '348/355' started by RandyT, Jun 15, 2022.

This site may earn a commission from merchant affiliate links, including eBay, Amazon, Skimlinks, and others.

  1. RandyT

    RandyT Formula Junior

    Aug 16, 2016
    258
    Calabasas, CA
    Full Name:
    Randy T
    #1 RandyT, Jun 15, 2022
    I'm trying to remove the rear headliner in my 1990 348 TS because the upholstery is falling down. I removed the dome light, removed the two screws inside the dome light, but I can't get the front edge of the rear section loose where the removable top "posts" go in. I can't figure out what's holding the front edge on. I don't see any other screws. There's no other screws on the outside of the panel as shown in other posts from F-Chat.

    If someone has done it before and knows, please reply. I only hope I don't need to remove all the upholstery behind the seat just to remove the rear headliner.

    Image Unavailable, Please Login Image Unavailable, Please Login
     
  2. 348Jeff

    348Jeff Formula 3

    Oct 25, 2011
    1,531
    UK
    Full Name:
    Jeff
    #2 348Jeff, Jun 15, 2022
    steved033 and Mike Morrissey like this.
  3. 348Jeff

    348Jeff Formula 3

    Oct 25, 2011
    1,531
    UK
    Full Name:
    Jeff
    #3 348Jeff, Jun 15, 2022
    Mike Morrissey likes this.
  4. RandyT

    RandyT Formula Junior

    Aug 16, 2016
    258
    Calabasas, CA
    Full Name:
    Randy T
    #4 RandyT, Jun 15, 2022
    Mike Morrissey likes this.
  5. 348Jeff

    348Jeff Formula 3

    Oct 25, 2011
    1,531
    UK
    Full Name:
    Jeff
    #5 348Jeff, Jun 15, 2022
    Your welcome.

    I did that job 8 years ago and its started coming loose on one side but cant bring myself to pull it all out again! LOL

    When I do it again I'll try and take some better photos :)
     
    Mike Morrissey likes this.
  6. mark348ts

    mark348ts Rookie

    Dec 8, 2022
    2
    Full Name:
    Mark Donald Staszewski
    #6 mark348ts, Feb 27, 2023
    /Did you use new foam and if so where did you get it from? What size bit did you use to drill out the rivits
     
  7. RandyT

    RandyT Formula Junior

    Aug 16, 2016
    258
    Calabasas, CA
    Full Name:
    Randy T
    #7 RandyT, Feb 27, 2023
    Hello mark348ts, I didn't redo it myself. I had a Ferrari upholstery expert do it in SoCal. I used a very small drill bit, maybe 1/8"?
     
  8. mark348ts

    mark348ts Rookie

    Dec 8, 2022
    2
    Full Name:
    Mark Donald Staszewski
    #8 mark348ts, Feb 28, 2023
    Do you remember the cost?
     
  9. RandyT

    RandyT Formula Junior

    Aug 16, 2016
    258
    Calabasas, CA
    Full Name:
    Randy T
    #9 RandyT, Feb 28, 2023
    Around $400
     
  10. marknado

    marknado Karting

    Mar 4, 2021
    51
    New Zealand
    Full Name:
    Mark
    #10 marknado, Feb 28, 2023
  11. User-C3

    User-C3 Karting

    Aug 29, 2018
    240
    Detroit
    Full Name:
    Trevor
    #11 User-C3, Mar 6, 2023
    I did mine and used new foam. Got the foam from Joann fabric. Pretty cheap and easy to find stuff other places as well. Its not a hard job, just a bit of a pain to get out and back in.
     

Share This Page