360 coupe, interior diagram, how to take apart? | FerrariChat
Buy

360 coupe, interior diagram, how to take apart?

Discussion in '360/430' started by TZL, Jun 3, 2010.

This site may earn a commission from merchant affiliate links, including eBay, Amazon, Skimlinks, and others.

  1. TZL

    TZL Formula Junior

    Dec 15, 2003
    289
    Atherton, CA
    #1 TZL, Jun 3, 2010
    Anyone have a diagram or manual on how to take out the various interior trim panels etc?
     
  2. 360trev

    360trev F1 Rookie
    Project Master

    Oct 29, 2005
    4,330
    Gibraltar
    Full Name:
    360trev
    #2 360trev, Jun 3, 2010
    Get yourself a copy of the Workshop Manuals (WSM's). Invaluable and available on the web.

    You'll also need a set of Torx drivers. Be prepared to buy a few replacement plastic clips too, the part number for the plastic plug's/clips is 66092400. These ALWAYS break when dismantling the panels. They are one way plastic retainer clips and cost just a few cents each. If you don't buy a few you'll have an interior that forever more creaks... Not nice, don't botch it!
     
  3. AlanWard

    AlanWard Formula Junior
    Rossa Subscribed

    Apr 1, 2010
    703
    Boulder, CO
    Full Name:
    Alan Ward
    #3 AlanWard, Jun 3, 2010
    I have the workshop manual in PDF. Can't remember where I downloaded it from but PM me if you can't find it.

    Alan
     
  4. TZL

    TZL Formula Junior

    Dec 15, 2003
    289
    Atherton, CA
    #4 TZL, Jun 3, 2010
    as an follow-up: anyone know how to remove the vents at the base of the windshield? I would like to refinish mine

    any ideas? just pull on them?
     
  5. tazandjan

    tazandjan Three Time F1 World Champ
    Lifetime Rossa Owner

    Jul 19, 2008
    39,166
    Clarksville, Tennessee
    Full Name:
    Terry H Phillips
    #5 tazandjan, Jun 4, 2010
    TZL- They are held in by plastic "springs" on the body with a barb on the end to keep them from falling out. Radio removal tools or something thin and flexible can be used to push in the spring/barb catch and they pull right out. Or pull them out until you can see the "springs" and then push in on the "springs" while pulling.

    Taz
    Terry Phillips
     
  6. TZL

    TZL Formula Junior

    Dec 15, 2003
    289
    Atherton, CA
    #6 TZL, Jun 24, 2010
    Thanks Alan!

     
  7. TZL

    TZL Formula Junior

    Dec 15, 2003
    289
    Atherton, CA
    #7 TZL, Jun 24, 2010
    Anyone have any idea how to take out all the roof trim panels? the manual from Alan War has everything except that...the section says "under development" lol
     
  8. brian.s

    brian.s F1 Rookie
    Professional Ferrari Technician

    Nov 3, 2003
    3,809
    Midwest
    Full Name:
    Brian
    #8 brian.s, Jun 25, 2010
    They come out from the front back. Remove the apillar trims, then you see the bolts for the front half, then the back half, then the rear quarters. Not too hard, just look carefully, about a dozen fasteners but the sections do have those annoying little slip joints. Takes about 2 hours to strip interior.
     
  9. TZL

    TZL Formula Junior

    Dec 15, 2003
    289
    Atherton, CA
    #9 TZL, Jun 30, 2010
    Brian,

    Aftrer a couple hours last night, figured it out

    Actually mine comes out back to front

    1) remove dome light and vanity mirrors and screws, wait, as that piece is help by screws under the side panel
    2) remove seatbelts, 17mm hex on top
    3) pull back on b-pillars, exposing screw on top
    4) unscrew that to remove top piece in back
    5) pull down side plates
    6) unscrew the screws holding down the front piece, exposing screws holding the a-pillars

    I ordered all new fastners from Ricambi for a tight fit when i put it all back together

     

Share This Page