Are these oil hoses accessible/replaceable with engine IN | FerrariChat

Are these oil hoses accessible/replaceable with engine IN

Discussion in 'Boxers/TR/M' started by xplodee, Apr 30, 2019.

This site may earn a commission from merchant affiliate links, including eBay, Amazon, Skimlinks, and others.

  1. xplodee

    xplodee Formula 3

    Jan 3, 2017
    1,101
    Allentown, PA
    Full Name:
    Tim
    #1 xplodee, Apr 30, 2019
    Hi All-

    Are the two lines indicated in the pic below replaceable while the engine is in? We ran into a snag sourcing the longer of the two (dont recall which one that is) while doing my engine out.

    If we put the engine back in, can I replace the line in question later on this summer with the engine in?

    Thank you,
     

    Attached Files:

  2. Rifledriver

    Rifledriver Three Time F1 World Champ

    Apr 29, 2004
    34,091
    Austin TX
    Full Name:
    Brian Crall
    #2 Rifledriver, Apr 30, 2019
    Sure. A little easier with engine out but not that bad with it in.
     
    turbo-joe and xplodee like this.
  3. xplodee

    xplodee Formula 3

    Jan 3, 2017
    1,101
    Allentown, PA
    Full Name:
    Tim
    #3 xplodee, Apr 30, 2019
    Thank you very much!
     
  4. turbo-joe

    turbo-joe F1 Veteran

    Apr 6, 2008
    8,929
    southwest germany and thailand
    Full Name:
    romano schwabel
    #4 turbo-joe, May 1, 2019
    you can replace, but may be you have to modify the big tool ( open wrench ) for loosen the nuts of the hoses at the filter housing
     
    wintech likes this.
  5. Rifledriver

    Rifledriver Three Time F1 World Champ

    Apr 29, 2004
    34,091
    Austin TX
    Full Name:
    Brian Crall
    #5 Rifledriver, May 1, 2019
    ???? I guess you dont use 2 wrenches like everyone else.
     
  6. Rifledriver

    Rifledriver Three Time F1 World Champ

    Apr 29, 2004
    34,091
    Austin TX
    Full Name:
    Brian Crall
    #6 Rifledriver, May 1, 2019
    Why would you need to modify anything? I just use standard wrenches.

    I can't figure out how some people make such simple things so hard.
     
  7. turbo-joe

    turbo-joe F1 Veteran

    Apr 6, 2008
    8,929
    southwest germany and thailand
    Full Name:
    romano schwabel
    #7 turbo-joe, May 1, 2019
    my standard wrench has been to thick. I could loose a little but not turn. so I had to cut some left and right from the open part of the wrench to turn more. so may be you have a thinner tool that you can turn?
    and I not do simple things the hard way - even I like to work - but the easy way
     
  8. Rifledriver

    Rifledriver Three Time F1 World Champ

    Apr 29, 2004
    34,091
    Austin TX
    Full Name:
    Brian Crall
    #8 Rifledriver, May 1, 2019
    I misunderstood. Yes, some wrenches can be too thick to counterhold the fitting.
     
    wintech and turbo-joe like this.
  9. todd6363

    todd6363 Formula Junior

    Jan 20, 2007
    270
    Ohio
    Full Name:
    Todd
    #9 todd6363, May 1, 2019
    Xplodee sent you a pm a month ago - Have 7 complete sets ( all 3 hoses) in stock
     
  10. Mr.Chairman

    Mr.Chairman F1 Rookie

    Mar 21, 2008
    2,987
    New Jersey
    Full Name:
    Robbie
    #10 Mr.Chairman, May 14, 2019
    LMAO. scratching my head as well.

    R
     

Share This Page