The BMW 3.0 CS was one of my favorite cars at the show. Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login
Hot rod built by the roadster shop for Jessie James. I love this color on the GT3RS. Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login
Nelson racings twin turbo big block motor Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login
Building a service counter. Installed a wide stair case to store parts above the offices keeping the floor clear. Image Unavailable, Please Login Image Unavailable, Please Login
Carbench data sheet showing attachment points to the chassis. The tech support from Car bench is great, they are able to provided chassis data sheets back to the 60s. Image Unavailable, Please Login
Grinding the center of the shops floors and detail bays. Snuck some little munchkin hide and seek in. Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login
My dad running new airlines in the shop. He's a retired contractor who loves working with his hands, we barter construction labor for mechanical work. Give him an import beer and he can go all day with stories of the old country. Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login
Probably a bit late to post this Dan, however, you should check this stuff out for air - it's great We used it all thru our shop. http://www.rapidairproducts.com/page/fastpipe You can see some in this photo. Image Unavailable, Please Login
Our Car bench 4.2 Muraena with scissor lift, jig kit and pinch weld clamps in from Massa, Italy. Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login
It's really not. We only spent $3500 on materials for an 8000 Sq. Ft shop with quite a few drops. What so nice about it (aside from looks) is it's super flexible. Again, huge congrats on the equipment - all top notch!
Thats not as bad as I thought, I know aluminum pipe is outrageous. I think we spent $200 total on black pipe its dirt cheap and just reused valves we had. Thank you I can't wait to start using it all.
Our local township issued up a permit install the Spray booth and mixing room! Image Unavailable, Please Login
Fresh off the boat from Verona!! Our USI Italia Master series spray booth with mixing room. It's a fully heated downdraft booth. Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login
Spray booth "basement" assembled. We did an above ground installation with ramps to avoid cutting the floor and building a pit. The booth is a full downdraft system that pulls the air down into the floor, through filters, heats it, and recycles the heated air back into the booth. Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login
Epoxy floor primer coat. It goes on a wet floor to soak into the concrete. Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login
Air plenum installed. 15 HP motors! Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login
Walls going up. Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login
Ceiling and air induction framed out, lighting panels installed. On the right side of the booth we added a USI Italia mixing room. It's 3 sided so the painter can mix the paint and step directly into the booth avoiding contamination. Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login Image Unavailable, Please Login
