Novitec NF1 | FerrariChat
Buy

Novitec NF1

Discussion in 'Ad Archives' started by redlightrich, Dec 20, 2013.

This site may earn a commission from merchant affiliate links, including eBay, Amazon, Skimlinks, and others.

Page 1 of 2
  1. redlightrich

    redlightrich Karting

    Jul 28, 2009
    98
    north New Jersey USA
    Full Name:
    Rich
    #1 redlightrich, Dec 20, 2013
    Last edited by a moderator: Sep 7, 2017
    Hello, this is a set of NF1 centerlocks. I have the adapter kits as well. They came off a 430 but will fit 360 as well. They are 19" front and 20" rear.
    The tires mounted are Michelin Pilot Super Sports with less than 100 miles.

    These wheels are very nice, but not absolutely flawless. There is a small chip on 2 wheels. I did not fix them before the picture, as I wanted to display the minor flaws.

    I will certainly fix them before shipping.

    I am open to offers over 7000. for the set, including all needed hardware to mount.

    Thank you

    Rich
    Image Unavailable, Please Login
    Image Unavailable, Please Login
    Image Unavailable, Please Login
    Image Unavailable, Please Login
     
  2. tazandjan

    tazandjan Three Time F1 World Champ
    Lifetime Rossa Owner

    Jul 19, 2008
    39,020
    Clarksville, Tennessee
    Full Name:
    Terry H Phillips
    #2 tazandjan, Dec 21, 2013
    Rich- Those are NF1 wheels.
     
  3. redlightrich

    redlightrich Karting

    Jul 28, 2009
    98
    north New Jersey USA
    Full Name:
    Rich
    #3 redlightrich, Dec 22, 2013
    Hey Taz fancy seeing you here. Thanks for the correction!!!
     
  4. redlightrich

    redlightrich Karting

    Jul 28, 2009
    98
    north New Jersey USA
    Full Name:
    Rich
    #4 redlightrich, Jan 7, 2014
    I am not sure how to update the title, but as you can see I made a mistake and listed these as 3s.

    These are NF1s.

    All the pieces for adapting them to a 430/360 are included.

    Price reduced to 6000. Shipped to the continental USA. The tires mounted are virtually new with just pick up mileage.

    Thank you

    Rich
     
  5. tazandjan

    tazandjan Three Time F1 World Champ
    Lifetime Rossa Owner

    Jul 19, 2008
    39,020
    Clarksville, Tennessee
    Full Name:
    Terry H Phillips
    #5 tazandjan, Jan 7, 2014
    Rich- One of the mods can change the title for you if you PM him. Have him change the title to Centerlock Novitec NF1s and you may generate more traffic. Had a set myself, but they cannot be made to fit a Maranello. Not sure who is the POC for the for sale section.

    They made NF3s for the F430, 19" F and 20" R, but do not think they did for the 360.
     
  6. redlightrich

    redlightrich Karting

    Jul 28, 2009
    98
    north New Jersey USA
    Full Name:
    Rich
    #6 redlightrich, Feb 2, 2014
    TTT with new price

    6000 Shipped anywhere in the continental USA. Again, these include the adapters( not pictured but included in price), so any standard 5 lug 360 or 430 will take these wheels. Rubber is near new too.

    [email protected] is a good way to get me being I don't get time to log on as often as I would like.

    Thank you

    Rich
     
  7. redlightrich

    redlightrich Karting

    Jul 28, 2009
    98
    north New Jersey USA
    Full Name:
    Rich
    #7 redlightrich, Mar 30, 2014
    TTT!!! Once again a big price drop, I am open to offers over 4000 dollars. Please note, the rubber is like new. They are Michelin Super Sports. This is 4 wheels and the center lug adapters for each wheel.

    These were balanced and are ready to go. I will entertain a lower price for pick up in North NJ, so I don't have to deal with shipping.

    Nice wheels, nice tires, nice price!!!

    Thank you

    Rich
     
  8. Teachdocs

    Teachdocs Formula Junior

    Sep 3, 2012
    568
    Kansas City area
    Full Name:
    Chad
    #8 Teachdocs, Mar 31, 2014
    Will these fit a Scud?
     
  9. tazandjan

    tazandjan Three Time F1 World Champ
    Lifetime Rossa Owner

    Jul 19, 2008
    39,020
    Clarksville, Tennessee
    Full Name:
    Terry H Phillips
    #9 tazandjan, Mar 31, 2014
    Affirmative, no problems fitting them to a Scud. Will be a tight fit for the 398 mm front brakes and 6 piston calipers, but so are the standard wheels.
     
  10. Teachdocs

    Teachdocs Formula Junior

    Sep 3, 2012
    568
    Kansas City area
    Full Name:
    Chad
    #10 Teachdocs, Mar 31, 2014
    PM. Sent.
     
  11. AlgaeHater

    AlgaeHater Formula Junior

    Sep 22, 2004
    321
    Bellevue, WA
    #11 AlgaeHater, Apr 1, 2014
    Are you sure NF1s will fit a Scud? NF3s require a rear spacer. Front calipers barely clear the backs of the spokes (we're talking 1mm of clearance).

    I've never seen NF1s installed on a Scud, only NF3s.
     
  12. redlightrich

    redlightrich Karting

    Jul 28, 2009
    98
    north New Jersey USA
    Full Name:
    Rich
    #12 redlightrich, Apr 5, 2014
    Last edited by a moderator: Sep 7, 2017
    Hello all again, In an effort to clear up any questions;

    The date codes on the tires are 4412 ( 44th week of 2012) they were mounted sometime September 2013.

    The sizes are as follows

    Front 255-30-ZR19
    Rear 325-25-ZR20

    I have decided to attach a picture of the mounting hardware. As a brief description, the factory axle ( wheel bearing ) nut is removed, and the stub axle threads in its place and is torqued. The gold plate is indexed as to act as a lock. It slides over the new stub axle and aligns with the wheel stud holes. The taper pins thread into where the wheel studs used to go, and get torqued. Then the wheel is slid in place, the large washer goes on, then the special nut ( pictured on stub with yellow clip).

    The nut has double safety to it. I can mount these in about 30 minutes a wheel.

    I have all the mounting hardware, although I only showed one set in detail.
    Image Unavailable, Please Login
    Image Unavailable, Please Login
    Image Unavailable, Please Login
     
  13. redlightrich

    redlightrich Karting

    Jul 28, 2009
    98
    north New Jersey USA
    Full Name:
    Rich
    #13 redlightrich, Apr 26, 2014
    To whoever just pm'ed me, they are still available. Make an offer. I tried to reply but your inbox is too full to accept any more messages.

    Thank you

    Rich
     
  14. 360Tom

    360Tom Formula 3

    May 9, 2013
    1,396
    Burbank, CA
    Full Name:
    Tom
    #14 360Tom, Apr 26, 2014
    Front 255-30-ZR19
    Rear 325-25-ZR20

    Is that not too wide for a 360? Or. Does the car need raised to accommodate this setup?

    I'm looking at purchasing a set of wheels now due to my current set rubbing. I'm running a 305 now. But it could be the offset on the wheels. I have a yellow 360.
    These might look better than what I was looking at.
    Do you have a pic of them on the car
     
  15. tazandjan

    tazandjan Three Time F1 World Champ
    Lifetime Rossa Owner

    Jul 19, 2008
    39,020
    Clarksville, Tennessee
    Full Name:
    Terry H Phillips
    #15 tazandjan, Apr 26, 2014
    Last edited by a moderator: Sep 7, 2017
  16. 1stiffler

    1stiffler Karting

    Jan 23, 2013
    50
    #16 1stiffler, Apr 27, 2014
    Terry,

    Will this set fit a standard F430 spider? The yellow ring, is that part of the wheel as well? Thx in advance.

    Anthony
     
  17. 360Tom

    360Tom Formula 3

    May 9, 2013
    1,396
    Burbank, CA
    Full Name:
    Tom
    #17 360Tom, Apr 27, 2014
    Pm me please Rich. I'd love to buy these.
     
  18. tazandjan

    tazandjan Three Time F1 World Champ
    Lifetime Rossa Owner

    Jul 19, 2008
    39,020
    Clarksville, Tennessee
    Full Name:
    Terry H Phillips
    #18 tazandjan, Apr 27, 2014
    These wheels will fit a 360 or an F430 without altering ride height. Most of the additional width goes on the inside. They are copies of the Enzo wheels designed specifically for the 360/F430.
     
  19. 360Tom

    360Tom Formula 3

    May 9, 2013
    1,396
    Burbank, CA
    Full Name:
    Tom
    #19 360Tom, Apr 29, 2014
    I'll update with some pics once they arrive :)
     
  20. tazandjan

    tazandjan Three Time F1 World Champ
    Lifetime Rossa Owner

    Jul 19, 2008
    39,020
    Clarksville, Tennessee
    Full Name:
    Terry H Phillips
    #20 tazandjan, Apr 29, 2014
    Last edited by a moderator: Sep 7, 2017
  21. 360Tom

    360Tom Formula 3

    May 9, 2013
    1,396
    Burbank, CA
    Full Name:
    Tom
    #21 360Tom, Apr 30, 2014
    That looks really nice. So is it just a cap to cover the lock nut?
     
  22. tazandjan

    tazandjan Three Time F1 World Champ
    Lifetime Rossa Owner

    Jul 19, 2008
    39,020
    Clarksville, Tennessee
    Full Name:
    Terry H Phillips
    #22 tazandjan, Apr 30, 2014
    Last edited by a moderator: Sep 7, 2017
    Tom- Yup, that is all it is. The OEM ones are unaffordable, $800 each last time I looked, but a simple facsimile would not be difficult to fab out of aluminum and using OEM center caps. Just a trim piece that fastens to the Novitec nut. Could even be a three wing spinner if you wanted one.

    Here is another possibility for an idea from the 599XX.
    Image Unavailable, Please Login
     
  23. 360Tom

    360Tom Formula 3

    May 9, 2013
    1,396
    Burbank, CA
    Full Name:
    Tom
    #23 360Tom, Apr 30, 2014
    That 599xx is awesome. Hmmm
    Have you already attempted to make a set?
    I think I could fab caps over at my buddies shop. He's has a cnc machine.
     
  24. RonnieRenaldi

    RonnieRenaldi F1 Rookie

    Aug 16, 2004
    2,686
    #24 RonnieRenaldi, Apr 30, 2014
    Tom, you bought these?
     
  25. tazandjan

    tazandjan Three Time F1 World Champ
    Lifetime Rossa Owner

    Jul 19, 2008
    39,020
    Clarksville, Tennessee
    Full Name:
    Terry H Phillips
    #25 tazandjan, Apr 30, 2014
    Tom- No, when we discovered there was no way to adapt them to my 575M, we quit and I sold them. I bought a new set of NF2s instead.

    But, as you can see, there are many simple designs that would look really nice.
     
Page 1 of 2

Share This Page