Radiopilot does it again - 308 Clock

Nick who?

My hour hand is a little off. Drives me nuts.

 

Need mine done too. Contact information please?

MB

 

Nice pics,

Mine works but can't be set as the reset knob is non-operational.

I'd like to get it fixed. Can you post a little more info on your clockmeister.

Thanks,
Paul

 

Hello... I'm Nick... if interested in the clock repair send me a PM... to see other clocks repaired visit the 'Techinal Q&A' thread under Veglia/Borletti clocks.

Nick

 

Thanks Nick, mine looks like a cigar room behind the glass

 

I just sent mine out to Palo Alto Speedometer.

Is there a difference in price or quality?

 

I've had work done by PAS and it was excellent. I've had work done by Nick and it was also excellent. The price difference? Expect to pay PAS about 5x more than Nick.

 

I just rec'd my 308's clock back from Nick and i can't believe it's the same one i sent in,the lens is crystal clear where it was very smokey! I can't wait to put her in. Thanks Nick,looks fantastic and great price!
Bill

 

Bill... glad you are happy with the results, would like to see it on the dash later with a pic if you can...

Cheers,

Nick

 

Radiopilot, is there a gasket behind the glass? My gauge has a little condensation on it and was wondering if that's the problem.

Ace (as in ace_pilot)!

 

There is no gasket, it's the lens against a black plastic frame, to reduce condensation I have drilled several holes above the plastic case (covered with a nylon filter fabric so dust doesn't get in) on my clock and I can say it never gets condensation, I do this with aircraft instruments to reduce fogging that aren't pressurized.

All the clocks I restore uses OPTIX lenses and are made to deter fogging, but I use an anti-fogging cleaner on the inside of the crystal just to be sure, I use FogTech anti-fogging wipes, but there are other anti-fogging solutions I know that work quite well.

The reason it fogs is the incandescent bulb, it heats the inside of the clock and therefore it condenses humidity (reason I put the series of holes in all my instruments).

Hope that clears (no pun intended) things up some.

Nick

 

radiopilot what is your contact info?

Gary
espada 8394

 

PM sent...

 

The best idea to avoid condensation for the incandescent bulb is to swap to a LED bulb. I've done it and it works perfect.

 

If you want to restore your milky Veglia clock plastic, see this thread.

http://www.ferrarichat.com/forum/showthread.php?t=223495

Cheers

 

Led bulbs work great if you can get the same lumens from the LED to light up the clear plastic ring that surrounds the clock to illuminate it, some have tried it before and it works with several 'super white LED's' but the 12V must be reduced to 3V to work and that means extra solid state components or a 12V-3V converter...

Regarding the do it yourself lens install... if you have the patience to not ruin the slim chrome ring and not damage it in the process then great... but I've seen a lot of these rings damaged beyond repair... I have several of these chrome rings for the 308 clocks in stock and they are very hard to come by... so if you don't feel comfortable removing the ring don't do it... ask all those I've repaired 308 clocks what the ring looks like in the back... you can't tell it's ever been removed (I have a special tool to remove the ring - not a screwdriver sure to cause a damaged chrome ring)...

I've seen the link posted above and see the damage to the ring... you'll see the chrome ring damage when the clock is installed on the car.

Cheers,

NicK

 

Thanks for the reply Nick.

Yes, you're right, the special tool to remove the chromed ring is very useful and "a must have" in this case. No question.

About swapping to LED, I post a shot with the results. Perfect. I've bought the LED by Internet, 12V ready to install. The colour choosen is cool white, so the blue colour. If you want to preserve the green original colour, you must choose LED in warm white. Try it. There's a great post about it.

Cheers
Image Unavailable, Please Login

 

Thank you Nick, my clock rocks looks just like brand new. Now if I can only get the P/N for the LED bulb that retains the green color, TIA.
Image Unavailable, Please Login

 

Mike,

Wow... that panel looks great with those two insrtuments looking good there...

Antonio... that clock looks great too... I haven't used the LED's on my clock but is something I will do the next time I need to replace the bulb on my instruments... good tips everywhere....

Cheers,

Nick

 

Looks great Mike!

I prefer the placement of these gauges over my 79 GTB which is somewhere under my left knee.

 

Thanks, did you get yours done yet?

 

Mike.

I've bought the LED bulbs on eBay. You must try these ones on warm white colour. The problem is that the bulb is too large, so you have to desolder the two units at the top, and make a bridge in order to close the circuit -unless the LED will not light after the operation-. The web address:
http://cgi.ebay.com/ebaymotors/6-SMT-LED-BA9-Miniature-Bayonet-Base-Bulb-Warm-White_W0QQitemZ130328380477QQcmdZViewItemQQptZMotors_Car_Truck_Parts_Accessories?hash=item1e582d443d
Image Unavailable, Please Login

 

Thanks Antonio, I'll give them a try

 

Just another little plug for Nick. Take note in the before pics that the adjustment lever is bent...Nick took care of that too! Great results, quick turn around, very reasonable pricing. Highly recomended!
Image Unavailable, Please Login
Image Unavailable, Please Login
Image Unavailable, Please Login
Image Unavailable, Please Login