removal of moulding and cover | FerrariChat
Buy

removal of moulding and cover

Discussion in '308/328' started by Agsurf5, Jul 20, 2011.

This site may earn a commission from merchant affiliate links, including eBay, Amazon, Skimlinks, and others.

  1. Agsurf5

    Agsurf5 Rookie

    May 29, 2011
    46
    #1 Agsurf5, Jul 20, 2011
    Last edited by a moderator: Sep 7, 2017
    i have been researching everywhere. apparently everybody knows how to do it, but me....
    how do you remove the cover from the side moulding on a 85 305 QV?
    separating part 24 and 28 from the attached (from ferrari parts).
    i do not want to break anything, but i'd like to run a wire up there for a radar detector...
    Image Unavailable, Please Login
     
  2. stevel48

    stevel48 Formula 3

    Jan 4, 2005
    1,998
    Metrowest MA
    Full Name:
    Steve (85 308 Owner)
    #2 stevel48, Jul 20, 2011
    I'm not sure what we're looking at. What page of trhe WSM is that?
     
  3. ClydeM

    ClydeM F1 World Champ
    Owner Rossa Subscribed

    Nov 4, 2003
    11,908
    Wayne, NJ
    Full Name:
    Clyde E. McMurdy
    #3 ClydeM, Jul 20, 2011
    On my 83 GTB - your vinyl at the top of #24 looks like it's tucked behind the moulding, right? carefully coax and untuck the vinyl out. careful not to rip it as its old. slide the vinyl down about 1" where you'll find a very small black phillips screw holding the molding to #28. take out the screw. The moulding is now held in place by a metal spring clip near the base. Slide the molding up & off it pops. reverse the process for install.
     
  4. i-velocita

    i-velocita F1 Rookie
    BANNED

    Sep 9, 2006
    2,520
    Colorado
    Full Name:
    James
    #4 i-velocita, Jul 20, 2011
    Piece 28 pops off with a putty knife. Piece 24 can be removed by drilling out 2 rivets. Piece 25 can be removed with either 6 or 8 small screws depending on the year - I think an 83 has 6 screws. Good luck.
     
  5. Agsurf5

    Agsurf5 Rookie

    May 29, 2011
    46
    #5 Agsurf5, Jul 20, 2011
    ricambi america
    308QV: Table 111 - TUNNEL AND ROOF

    28 ok with putty knife. i can imagine it. are they just clips of some sort?
    so it snaps back in?
     
  6. i-velocita

    i-velocita F1 Rookie
    BANNED

    Sep 9, 2006
    2,520
    Colorado
    Full Name:
    James
    #6 i-velocita, Jul 20, 2011
    Yep, it just pops on and off. I think there are 3 clips.
     
  7. Easyrider7467

    Easyrider7467 Formula Junior

    Nov 3, 2005
    980
    Northen N.J.
    Full Name:
    John
    #7 Easyrider7467, Jul 21, 2011
    When he pops #28 off what will be behind that trim?

    I ask this becuase I've been thinking of poping this off myself as well (1989 GTS) to check my drain tube for a clog. Not sure if its seen after popping #28 off.
     
  8. i-velocita

    i-velocita F1 Rookie
    BANNED

    Sep 9, 2006
    2,520
    Colorado
    Full Name:
    James
    #8 i-velocita, Jul 21, 2011
    Trim #24 is behind. Must drill out 2 rivets to remove #24.
     
  9. chairpilot

    chairpilot Formula 3

    Mar 3, 2007
    1,547
    LA, CA & Olympia, WA
    Full Name:
    PlateClipGuys
    #9 chairpilot, Jul 21, 2011
    +1 - I've done all this too.... easy process.
     
  10. Jdubbya

    Jdubbya The $10 Trillion Man
    Silver Subscribed

    Dec 28, 2003
    43,209
    PNW
    Full Name:
    John
    #10 Jdubbya, Jul 21, 2011
    Could be screws too. Mine was but I'm not sure if that was original or not. Yep the center trim piece just pops out.
     

Share This Page