Removing panel to access tail light bulbs | FerrariChat
Buy

Removing panel to access tail light bulbs

Discussion in '308/328' started by Easyrider7467, Oct 10, 2022.

This site may earn a commission from merchant affiliate links, including eBay, Amazon, Skimlinks, and others.

  1. Easyrider7467

    Easyrider7467 Formula Junior

    Nov 3, 2005
    980
    Northen N.J.
    Full Name:
    John
    #1 Easyrider7467, Oct 10, 2022
    Hello everyone,

    How many days should it take me to figure out at what precise position the quarter turn screw needs to be to pop out?

    thank you,
    John
    ‘89 328 GTS


    Sent from my iPhone using FerrariChat
     
  2. Rifledriver

    Rifledriver Three Time F1 World Champ

    Apr 29, 2004
    37,100
    Cowboy Capitol of the World
    Full Name:
    Brian Crall
    #2 Rifledriver, Oct 10, 2022
    Sometimes you have to pull on them a little. If the panel has pressure one way or the other that happens.
     
  3. Easyrider7467

    Easyrider7467 Formula Junior

    Nov 3, 2005
    980
    Northen N.J.
    Full Name:
    John
    #3 Easyrider7467, Oct 10, 2022
    Thank You Rifledriver !!

    I'll exercise further patience and heed your advice.. Gingerly coaxing them.
    How have you been? Hope you and your loved ones are doing well.
    Its been quite some time since my presence here.

    I have in the past and now greatly appreciate your guidance.

    Sincerely,
    John
    NJ
     
  4. Rifledriver

    Rifledriver Three Time F1 World Champ

    Apr 29, 2004
    37,100
    Cowboy Capitol of the World
    Full Name:
    Brian Crall
    #4 Rifledriver, Oct 11, 2022
    The other side may come easier. If that one comes out you will better see whats required.

    Everything is good. Good luck.
     
  5. Easyrider7467

    Easyrider7467 Formula Junior

    Nov 3, 2005
    980
    Northen N.J.
    Full Name:
    John
    #5 Easyrider7467, Oct 11, 2022
    Plutonium likes this.
  6. Easyrider7467

    Easyrider7467 Formula Junior

    Nov 3, 2005
    980
    Northen N.J.
    Full Name:
    John
    #6 Easyrider7467, Oct 11, 2022
    I initially turned the screw to get enough room beneath it, then while the angled pry tool maintained upward pressure, I turned the screw slowly until it popped. Seconds.


    Sent from my iPhone using FerrariChat
     
  7. Rifledriver

    Rifledriver Three Time F1 World Champ

    Apr 29, 2004
    37,100
    Cowboy Capitol of the World
    Full Name:
    Brian Crall
    #7 Rifledriver, Oct 11, 2022
    Good work.


    The cars are not made of glass. It is OK to pry on things from time to time.
     
    bitsobrits and Easyrider7467 like this.
  8. ChevyDave

    ChevyDave Formula Junior

    Dec 21, 2019
    411
    Pacific Northwest, USA
    Full Name:
    Dave W
    #8 ChevyDave, Oct 15, 2022
    Well, except for those pesky first 800 or so.....

    Sorry couldn't resist; Saturday afternoon, car's in the shop, and nothing better to do. :p
     

Share This Page