Replace Windstop under the roll bar | FerrariChat
Buy

Replace Windstop under the roll bar

Discussion in '360/430' started by redspyder, Mar 13, 2016.

This site may earn a commission from merchant affiliate links, including eBay, Amazon, Skimlinks, and others.

  1. redspyder

    redspyder Karting

    Jul 10, 2012
    67
    california
    Full Name:
    Steve Landaker
    #1 redspyder, Mar 13, 2016
    Guys how do you replace the windstop UNDER THE ROLL BARS on a 360?
    THANKS.
     
  2. 2NA

    2NA F1 World Champ
    Consultant Owner Professional Ferrari Technician

    Dec 29, 2006
    18,221
    Twin Cities
    Full Name:
    Tim Keseluk
    #2 2NA, Mar 13, 2016
    With the Spider top in the part way open position you can access the screws.
     
  3. redspyder

    redspyder Karting

    Jul 10, 2012
    67
    california
    Full Name:
    Steve Landaker
    #3 redspyder, Mar 14, 2016
    Is there any special tool needed? It looks like two screws per windstop.
    Do you have to recycle top and special way?
    THANKS,
     
  4. 2NA

    2NA F1 World Champ
    Consultant Owner Professional Ferrari Technician

    Dec 29, 2006
    18,221
    Twin Cities
    Full Name:
    Tim Keseluk
    #4 2NA, Mar 14, 2016
    Nothing fancy, just 2 screws. I think an 8mm wrench. Cycle the top until you can get to the screws, stop part way. Not a big job but watch your fingers if the top starts to move.
     
  5. redspyder

    redspyder Karting

    Jul 10, 2012
    67
    california
    Full Name:
    Steve Landaker
    #5 redspyder, Mar 14, 2016
    Tim, thanks A LOT for the INFO!
    Steve
     
  6. redspyder

    redspyder Karting

    Jul 10, 2012
    67
    california
    Full Name:
    Steve Landaker
    #6 redspyder, Mar 17, 2016
    Tim,
    Spend 2 hours replacing the windstops with new ones as rubber seals around screen were sticky and cracked. My 2 screws on each windstop were allen screws, which were hard to get the allen wrench on the two outside corner screws.
    Done and the new windstops LOOK GREAT!
    Thanks,
    Steve
     
  7. fedwin3

    fedwin3 Rookie

    Apr 11, 2012
    9
    #7 fedwin3, Mar 17, 2016
    Where did you buy the windstops? Cost?
     
  8. redspyder

    redspyder Karting

    Jul 10, 2012
    67
    california
    Full Name:
    Steve Landaker
    #8 redspyder, Mar 18, 2016
    Ricambi America $631.44 for both.
     
  9. My2001360

    My2001360 Rookie

    Jan 1, 2016
    1
    Full Name:
    Marvin Metzler
    #9 My2001360, Apr 23, 2016
    What did you do with the old windstops?
     
  10. dickgeorge

    dickgeorge Rookie

    Aug 8, 2010
    13
    Texas USA
    Full Name:
    Dick George
    #10 dickgeorge, May 31, 2016
    I was able to buy rubber gasket that works on the 360 windstops. It is described on Ebay as Windshield Auto Glass Push In T shape Molding Flexible Trim Rubber. It is the right width and the spline fits perfectly to hold in the mesh. Not including removal from the car, replacing the rubber took about 20 minutes each. Very hard to find this rubber and I was glad it worked out perfectly. Looks great.
     

Share This Page