Rusty 308gtb restoration | FerrariChat

Rusty 308gtb restoration

Discussion in '308/328' started by dwil, Sep 11, 2006.

This site may earn a commission from merchant affiliate links, including eBay, Amazon, Skimlinks, and others.

  1. dwil

    dwil Karting

    Nov 8, 2003
    114
    ozarks
    Full Name:
    Dave Wilson
    #1 dwil, Sep 11, 2006
    Last edited by a moderator: Sep 7, 2017
    Finally I am getting around to restoration on my gtb.
    First order of business is to repair the widespread corrosion
    in the rear. This is what I found when I took it apart:

    The last time this car was painted someone "repaired"
    the rust with a bunch of bondo and fiberglass. The worst
    areas are the lower areas of the rear fenders and luggage
    compartment floor. Most of the damage seems to have
    been caused by moisture trapped by the insulation and
    carpeting in these areas. I plan on mig welding in panels
    to replace the compartment floor, and trying something
    new to me for the outer sheet metal which is mig brazing.
    Has anyone here tried mig brazing for rust repair? It is
    suppose to be great for non structural panel replacement
    as it runs about 500 degrees cooler than welding.
    I picked up the bronze mig wire but haven't yet got a
    tank of pure argon to practice with yet.
    Progress will be posted and advice or suggestions will
    be greatly appreciated!
    Image Unavailable, Please Login
    Image Unavailable, Please Login
    Image Unavailable, Please Login
    Image Unavailable, Please Login
     
  2. flyingboa

    flyingboa Formula 3

    Nov 27, 2003
    1,564
    Italy
    Full Name:
    Eugenio Dalla Rosa
    That really seems quite a job. Good luck and keep us posted.
    Ciao
    Eugenio
     
  3. PenP

    PenP Formula Junior
    Rossa Subscribed

    Jun 20, 2006
    666
    Los Angeles
    Full Name:
    Pen Pendleton
    Damn!! Was your trunk used as an ice chest?!! A road-salt receptacle? Good luck - very cool that you're trying to do it yourself AND learn some new tricks while you're at it.
     
  4. SFchallenge

    SFchallenge F1 World Champ

    Jun 28, 2004
    11,945
    Sgp, KL, HK & London
    Full Name:
    Jon Wijaya
    Another hero is born, please keep us posted on your project. Will it be a full-blown project? Sorry, I can't help much on the welding info & I've only done argon on aluminium but you can try this http://en.wikipedia.org/wiki/Mig_welding
     
  5. racespecferrari

    racespecferrari F1 Veteran

    Jan 31, 2006
    7,583
    Suffolk, Uk
    Full Name:
    Pete.G By The Sea
    Ditto, you are a braver man than I am, hope it all goes well
     
  6. dwil

    dwil Karting

    Nov 8, 2003
    114
    ozarks
    Full Name:
    Dave Wilson
    Thanks!
    Encouragement from LA, Singapore, Italy and UK-where else but Fchat
    could you get that!
    I am not doing a total restoration like Paul Newmans, just decent
    driver quality paint that will last. This car came from the northeast
    and must have been subjected to the elements on a regular basis.
    It has had sheet metal replaced in the lower portions of the doors
    ar some point which will have to be redone because they weren't
    painted on the inside and are rusty. Also I removed the windshield
    (did not break :) ) and there are rust perforations in that area.
     
  7. Verell

    Verell F1 Veteran
    Consultant Owner

    May 5, 2001
    7,022
    Groton, MA
    Full Name:
    Verell Boaen
    A lot of the early 308s didn't have paint on the inside of the doors, so don't assume that it was replaced panels, may have been Ferrari's fault.

    re: MIG Brazing
    I've got the wire & Argon, but haven't used it.

    One nice thing about the 308 body panels is that they're fairly heavy gauge old fashioned mild steel. They don't tend to warp when heated the way the thin high strength steel body panels used on most cars built since the early '80s.

    The 308 panels are a real pleasure to work on with body tools. They respond very nicely & predictably.

    BTW, here's a tip: Get your repair metal from a commercial airconditioning shop instead of a auto body supply shop. The commercial A/C shops stock 20 Gauge galvanized mild steel panels in sizes up to 4' x 8'. It's also mild steel & works easily. The galvanizing provides significantly better protection than the thin electro-galvanizing on std body repair panels.

    Got this tip from a show car building/classic car restoration shop years ago.
     
  8. Peter

    Peter F1 Veteran
    Owner

    Dec 21, 2000
    6,440
    B.C., Canada
    Be sure to emphasize to our readers that anywhere there is galvanizing near the area to be welded, should be removed (grounded, or buffed off to bare metal) as the fumes produced when the galvanizing melts is very toxic... You get what's called the "zinc chills", where you start to shake uncontrollably (it attacks your nervous system). I got that once when I first started welding years ago. Drinking milk helps to get rid of the symptoms, but the damage is already done at that point.

    Just thought I should point that out.

    As for MIG brazing, I don't understand. TIG brazing yes, but MIG, no. "Metal, Inert Gas" refers to the use of the filler metal as the electrode and is therefore consumed in the welding process. Kind-of like stick welding, but instead of the flux from the stick, you use a gas for the weld area shielding. "Tungsten, Inert Gas" refers to the use of a non-consumed, tungsten electrode to provide the heat source, to melt a hand (or even sometimes in production processes, machine)-fed filler metal. For brazing, the "TIG" torch can be run at lower temps for brazing, just like an oxy-acetylene torch.
     
  9. Verell

    Verell F1 Veteran
    Consultant Owner

    May 5, 2001
    7,022
    Groton, MA
    Full Name:
    Verell Boaen
    Technically 'Brazing' is the use of a lower melting point metal (typically a Cu alloy) to join two pieces of metal.

    'MIG Brazing' uses a bronze wire instead of a steel wire as the filler metal. The bronze wire has a fairly low melting point, hence you can a much lower current setting than steel wire, and heat the metal being joined less.

    Good point about grinding back the zinc on a galvanized pane. Was taking that as common knowledge which I know better than to do on a general forum like this.
     
  10. Nickt

    Nickt Formula 3

    Feb 24, 2006
    1,741
    Iver, Buckinghamshir
    Full Name:
    Nick T
    I am sure I read somewhere that bodyshops now epoxy/glue repair panels on. Does any one have a view on this?

    Regards
    Nick
     
  11. Newman

    Newman F1 World Champ
    Consultant Owner Professional Ferrari Technician

    Dec 26, 2001
    14,465
    Canada
    Full Name:
    Newman

    Correct, its been used for almost 10 years here at our dealership. Im not a fan of it, seen it used to bond a repair panel onto a door and it failed. Maybe a roof pan or a full quarter replacement on something other than a ferrari or a high end car.
     
  12. thecarreaper

    thecarreaper F1 World Champ
    Silver Subscribed

    Sep 30, 2003
    18,071
    Savannah
    good to know !!! thanks !!!
     
  13. Nickt

    Nickt Formula 3

    Feb 24, 2006
    1,741
    Iver, Buckinghamshir
    Full Name:
    Nick T
    So is you recomendation is weld or braise?
    I only ask because I have a funny feeling that this time next year I might need a rear wheel arch repair panel or two!
    Cheers
    Nick
     
  14. Verell

    Verell F1 Veteran
    Consultant Owner

    May 5, 2001
    7,022
    Groton, MA
    Full Name:
    Verell Boaen
    The panel adhesives seem to be getting better and easier to use. Eastwoods just started carrying them, and they're pretty good about making sure their products perform well. As with any adhesive, surface preparation is critical to ensure good bonding.

    However,
    An adhesive is like any other plastic, it'll age. If you want the repair to last 10-20 years or more, I wouldn't use an adhesive at this point in time.

    This may be overly cautious as I know that the aircraft mfgs are starting to make extensive use of structural adhesives, and jetliners have expected airframe lifetimes of 30 years or more.
     
  15. wrecktech

    wrecktech Formula Junior

    Jun 4, 2004
    368
    Fort Wayne, Indiana
    I would use a mig welder and use a wet rag to cool and help keep the metal straight. when welding a long line, spot weld and tack it in every 1.5 inches or so and then go back and keep tacking until it is welded solid. The glues will not work well on rusty panels. I would sandblast as much as possible and use por 15. If you were closer I would give you a hand.
     
  16. Nickt

    Nickt Formula 3

    Feb 24, 2006
    1,741
    Iver, Buckinghamshir
    Full Name:
    Nick T
    Hi Wrecktech
    What is POR 15?

    Rgds
    Nick
     
  17. wrecktech

    wrecktech Formula Junior

    Jun 4, 2004
    368
    Fort Wayne, Indiana
    It is a rust converter/preventor. Fantastic product
     
  18. rolindsay

    rolindsay Formula 3

    Jul 14, 2006
    1,022
    Houston, TX
    Full Name:
    Rick Lindsay
    Agreed! I use it on the inside of panels where repairs are made (not on a Ferrari) and no rust has come through.
     
  19. Verell

    Verell F1 Veteran
    Consultant Owner

    May 5, 2001
    7,022
    Groton, MA
    Full Name:
    Verell Boaen
    POR15 is a paint that completely blocks both oxygen & moisture. You mecnanically (wire brush, media blast, whatever), degrease the surface, use a phosphate conversion etch to 'kill' any remaining rust, then paint on 2-3 coats of the POR15 coating to completely seal it. You can then prime & paint over the POR15 if necessary.

    Kits are available that have the surface cleaner, 'Metal Ready' phosphate conversion etch, & POR15 coating.

    It's really great stuff. Well known in the classic car restoration crowd.

    I used it a 3 years ago on my 308 when removing some rust bubbles that had lifted the paint, but had only a couple of pinholes thru the panel. I treated both sides of the panel, then refinished the outside using standard techniques. So far no sign of recurrance.

    Most auto body supply shops have started carrying it.

    See: www.por15.com
     
  20. rolindsay

    rolindsay Formula 3

    Jul 14, 2006
    1,022
    Houston, TX
    Full Name:
    Rick Lindsay
    Critical point there. This is a product that works best when it completely encapsolates the once rust infected area. Finishing the BACK side of a repair that has rusted through is essential.

    I repaired an MGB not too long ago where the lower edges of the doors were starting to show pin-holes of rust. The correct procedure was of course to cut away the bad metal and weld in new metal. This car didn't warrant that degree of attention. I ground/wire brushed/sanded the exposed outer and lower surfaces then from the inside of the door I wire brushed away as much rust as possible. I then vacuumed everything clean, flushed the phosphate prep inside and out and once dry, applied POR15 to the inside of the door to the point where every surface of the inner lower door was coated and the seams were saturated. I then repeated the process on the outside surfaces. From there, it was just a case of a little bodyfiller and sanding and the repair was ready for paint. One point to keep in mind: POR15 when cured is VERY HARD. If you're going to be sanding afterwards, be careful with the application. Fill with level with filler rather than sanding this pseudo-stone!

    I really feel that the key is to seal or encapsolate the rusted area completely in the POR15 product THEN finish as usual.
     
  21. andrewg

    andrewg F1 Rookie
    BANNED

    Sep 10, 2002
    4,667
    Chester, England
    Full Name:
    AndrewG
    Nick,
    Our version of eastwood's, Frost's stock it if you need any :)

    http://www.frost.co.uk/
     
  22. Peter

    Peter F1 Veteran
    Owner

    Dec 21, 2000
    6,440
    B.C., Canada
    Thanks, I wasn't aware of that and have not seen these spools of "brazing wire" at our local welding suppliers.

    Any special gases used with this process and/or the use of a paste flux for the weld area?
     
  23. Verell

    Verell F1 Veteran
    Consultant Owner

    May 5, 2001
    7,022
    Groton, MA
    Full Name:
    Verell Boaen
    You have to use Argon to shield & cool the wire.

    I had to have my local welding supplier order the silicon bronze wire. They hadn't heard of it & had to look it up. Think they were just being polite, as they looked a bit surprised when they found it. Anyway, I go a 1-lb spool for around $35. Probably more now that copper's jumped from $0.50/lb to almost $3/lb.
     
  24. dwil

    dwil Karting

    Nov 8, 2003
    114
    ozarks
    Full Name:
    Dave Wilson
    #24 dwil, Sep 18, 2006
    Last edited by a moderator: Sep 7, 2017
    Haven't got around to getting the pure argon cylinder yet but for those interested here's some info:http://www.cadvision.com/blanchas/54pontiac/mig-brazing.html
    BTW the welding supply in the link just sold me a couple of roll of the
    wire for about $20 each plus shipping(they were 2 lb rolls)

    Just a little progress has been made on my project. The boxes that
    covered the sides of the frame were removed and new ones were
    made. Being very inexperienced with metalwork, I tried to measure
    and transfer the measurements directly onto the metal then cut and
    brake/bend them. What I had after a few hours was a small pile of
    ones that didn't fit. Probably one of the basics to you guys that know,
    I realized that you need to make a template out of cardboard. This
    helped a lot. Also I was cutting them out with a pair of dull shears,
    then remembered I had bought an relatively cheapo plasma cutter
    several years ago but had been too lazy to set it up. What a difference!
    Clamp a straight edge to the metal to guide the torch and you slice
    through the metal as easy as cutting paper with a razor!
    The boxes I made are not exactly like the original in detail but
    will do an effective job in sealing that area. I also decided to
    pop rivet them in place so that the metal surfaces can be coated
    with por 15 inside and out.
    Image Unavailable, Please Login
    Image Unavailable, Please Login
    Image Unavailable, Please Login
     
  25. ckracing

    ckracing Formula Junior

    May 20, 2006
    728
    Jacksonville,Florida
    Full Name:
    Charles
    Phosphoric acid turns iron oxide(rust) to iron phosphate(black). You must wash off the treated area, because of acid residue.
    Purchasing the chemical, phosphoric acid from a chemical supply house is less expensive than buying a commercial product of "Rust Begone",etc.
    Use plenty of ventilation, the fumes are dangerous, acid mist.
    Good luck
    Charles
     

Share This Page