308 jack kit plastic part

Sure, how much are we talking?

 

I haven't had a chance to estimate costs yet. Need to look at the mold design & figure yields. Give me a couple of weeks, this is my busy season & I'm backed up with current orders.

 

Count me in! see here: http://www.ferrarichat.com/forum/showthread.php?t=51224

 

I just looked at my 328 jack, I think it may be different to the 308 jack. The plastic hand wheel is attached to the jack itself (rather than the extension handle) and is not easily removed.
My jack is in excellent condition, I expect it has never been used.

 

Mine is missing also. I'd take one for the right price. BTW, anyone know what it was for?

Joe

 

It's a hand wheel for quickly spinning the lugs out after the wrench breaks them loose, at least how I use it....

Same thing in reverse upon reassembly....

 

Making the mold is moving up on my list, looks like I'll get to the mold by mid March.

Unless it proves a real problem to cast, it'll probably be around $40.

 

I'm overseas at the moment, but I'll check my jack kit when I get home. If mine's missing, I'll order one as well.

 

I checked my jack and the plastic wheel is in perfect condition. Verell, do you need one to construct your sample part?

 

Hmm,
While mine is in pristine condition, if I had a 2nd one, I could make 2 at a time which would help keep the cost down.

So, yes' I'd like to borrow it for a couple of weeks.

 

Let me take a pic of the part I think you need to make sure I send the correct "thing-a-ma-bob".

 

Verell, is the black thumb wheel what you need?
Image Unavailable, Please Login
Image Unavailable, Please Login

 

Hello Greg,
That's a different thumbwheel from mine, or else the design changed over the years!!!


Could that be a 328 jack (See GXI328's post earlier in this thread).

I never looked to see if my thumbwheel would also fit onto the jack. However, since the ratchet wrench fits both fittings, I suspect it would. If so, then I think there must have been a design change at aome point. My thumbwheel looks quite a bit heavier than yours.

 

Interesting...now I guess I need to look for an original 308 jack...damn!

 

It's a 308QV jack; same as mine.

I need the nylon piece behind the thumbwheel, though it looks like the top nut of the 2 on the jack, is welded to to the shaft.

Does anyone know if the nylon bushing can be replaced?

 

No the hex on the jack is much larger than the shaft drive that fits into the ratchet.

The hex on the shaft drive is smaller....

 

Greg, your jack appears OEM to me as the rest of it is the same...maybe they just reworked the drive part assemblies?

I have all my thumbwheels, V. if no one else can help.....

 

Hello from Germany,

paint it yellow and buy a handle ring / wheel from Verell and it will be 308

Best Regards

Martin

 

Yellow?!?

 

yes, like this one for example. It looks like mine.

http://cgi.ebay.com/ebaymotors/Ferrari-250-275-308-330-365-512bbi-Jack-Bag-N-R_W0QQcmdZViewItemQQ_trksidZp1638Q2em122QQcategoryZ6763QQihZ007QQitemZ170195440633QQrdZ1QQsspagenameZWD2V

don't know, when they began with black ones. Mine is a carbed, albeit late, GTB. Maybe a black one for your QV is correct . But who cares ?

Best Regards from Germany

Martin

 

I've never seen the yellow ones.

Who cares? Man, you've never been to a FCA event here in the States then. Man those people are anal!