Fabspeed Headers Group Buy!

ok, you guys have seen the thread on their headers:

http://www.ferrarichat.com/forum/showthread.php?t=179060

Now it's time to step up and place an order! I spoke with them briefly and they said if we can round up a confirmed 4+ Fchat orders we can get a better price. And they have headers on the shelf ready to ship, both 2.7 and 5.2 versions. I need headers now, so hopefully we'll get 4+ guys within a week or two. If not I'm just ordering on my own.

Send me a PM with contact info if you're in -
Image Unavailable, Please Login

 

Shoot me the price over PM... If the price is equal to or "BETTER" than what I saw them for on the web I am in... I also sent you a PM.. I am ready NOW!!! Engine is out at the shop so the sooner the better.. I need to take a DRIVE!!!

 

Hi Jay

whats the price for the 2.7?

Thx
Chas

 

I am definitely interested. Do we have any numbers yet? Is there a performance gain/drain?

Steve

 

ok here's the deal guys:

If we get 5+ confirmed orders, they'll drop the price to $2345 plus FREE shipping! Heck at that price you can buy a set just to hang on the wall as art work!

Best part is they're warrantied for life - if they ever crack or fail they'll repair or replace...in other words, no worries. Check their website, www.fabspeed.com

If you've been thinking of ditching the OEM headers that WILL fail eventually, now's the time to jump in. Myself and F355 Spider need to order ASAP, so if we don't get 3 more takers within a week or two the group buy will be off

PM me contact info if you're in - phone / address (free ship to continental US only)

This is for both 2.7 and 5.2 Motronic 355's; they have both in stock and ready to ship, no waiting for months on backorder...

 

http://www.ferrarichat.com/forum/showthread.php?t=179060&highlight=355+headers+fabspeed

 

That equates to $150 off each set and free shipping---pretty good deal!!!

 

I may be interested. Say, is there a heat shield required on these do you know? They are some great looking headers!! $2,345 I assume that for each?

 

Heat shields are highly recommended with any headers - I plan to make a shield for the alternator and motor mounts, and to shield the brake lines and oil drain line. You can have the headers ceramic coated also, either on your own or Fabspeed can have it done (extra cost). I'm still undecided if I'm going ceramic or not.

I certainly assume price is for the set (Fabspeed, correct me if I'm wrong!)

 

Jump in Robbie, you know you want them!

 

I'm not from Fabspeed but have had my eyes on them for a while and know for a fact that the price is for the set.

 

Jay,

I have another confirmed person ready to order up here in Oregon.. So that puts us at, what 3 confirmed or 4???

 

Sonny if you and your buddy are confirmed (email / PM me address and phone #), then we have 4

1. Uconn Husky
2. OENGUS
3. F355 Spider
4. F355 Spider friend

One more and we can start placing orders!

 

Price is for the pair and the ceramic coating from Fabspeed is $300 extra... And stop tempting me!!!!

 

I am thinking about jumping in on this order, do I get a free Fabspeed shirt?

 

I'll buy you a T-shirt if you get in on it

 

Just an unrelated question. Do you guys expect better performance/weight saving on these customed headers alone? I'm getting a set of headers for my porsche from them as well. Would you guys ceramic coat it?

 

Hi Jon
small weight savings and apparently a few more hp. The ceramic coating is optional for decreased heat...........not sure if it would be necessary on a 911/993 etc etc

 

J---Can you get the specifics from him about the ceramic coatings? Colors? Do I need shields if I use the coating? Any testing of temp differences with coating or without? May look into a wrap like X did?

 

Mmmmm....very very tempting...

 

There's 2 reasons to coat / wrap headers - to improve performance by keeping the exhaust gas hot (and therefore keeping velocity high), and to minimize any heat damage to surrounding parts. On our 355 I doubt the performance change between coated / non-coated will be much (bigger deal on my STi where I have to keep a turbo spinning - I had those headers coated). Only concern is heat damage to surrounding parts. That can be mitigated with heat shields for the alternator, etc. Wraps are the best to keep heat in, I just don't care for the look...I want to show these things off!

Hey Jetfixr - have you measured header temps with an IR gun?

 

Hi Guys,'
I have a 1985 308QV and my office is next door to FabSpeed,You will be more then Happy with your purchase. They have an ultra clean shop with the best materials and tools and a great Team of guys. You will be smiling from ear to ear. Just wanted to say Fabspeed is top notch, If you tell Joe at FabSpeed Glenn was confirming his quality maybe he will throw in shirts for everyone
Good Luck
Captglen308

 

http://www.centuryperformance.com/heatwraps.asp

 

http://www.performancecoatings.com/

No affiliation with this company--just for the info...

 

Over the next few days--Anyone who has a IR gun--measure there header temps--we will then have an average temp across the board from various cars and an idea of what kind of wrap/coatings we need..I'll do mine tomorrow morning and post the temps.. Not sure how accurate my gun is--I guess I'll find out...